Teledyne 200E, Инструкция по эксплуатации, Страница: 139 / 302

Calibration Procedures Model 200E Instruction Manual
To program the sample sequence shown above, follow this flow chart:
SAMPLE RANGE = 500.0 PPB NOX=X.X
< TST TST > CAL CALZ CZLS
SETUP
SETUP X.X
PRIMARY SETUP MENU
CFG
ACAL DAS RNGE PASS CLK MORE EXIT
SETUP X.X SEQ 1) DISABLED
NEXT MODE EXIT
SETUP X.X SEQ 2) DISABLED
PREV NEXT
M ODE EXIT
SETUP X.X M ODE: DISABLED
NEXT ENTR EXIT
SETUP X.X MODE: ZERO
PREV
NEXT ENTR EXIT
SETUP X.X M ODE: ZERO–SPAN
PREV
NEXT ENTR EXIT
SETUP X.X SEQ 2) ZERO–SPAN, 1:00:00
PREV NEXT
MODE SET EXIT
SETUP X.X TIM ER ENABLE: ON
SET> EDIT EXIT
SETUP X.X STARTING DATE: 01–JAN–02
<SET SET>
EDIT EXIT
SETUP X.X STARTING DATE: 01–JAN–02
0 4 SEP 0 3 ENTR EXIT
Toggle keys
to set
day, m onth &
year:
Form at :
DD-MON-Y
Y
SETUP X.X STARTING DATE: 04–SEP–03
<SET
SET> EDIT EXIT
Default
value is
ON
SETUP C.4 STARTING DATE: 04–SEP–03
<SET
SET> EDIT EXIT
SETUP C.4 STARTING TIM E:00:00
<SET SET>
EDIT EXIT
SETUP C.4 STARTING TIME:00:00
1 4 : 1 5 ENTR EXIT
Toggle keys to
set time:
Format : HH:MM
This is a 24 hr
clock .
PM hours are
13 – 24.
Example
2:15 PM = 14:15
Toggle keys
to set
number of
days
between
procedures
(1-367)
Toggle keys
to set
delay time for
each iteration
of the
sequence:
HH:MM
(0 – 24:00)
SETUP C.4 DELTA DAYS: 1
<SET SET>
EDIT EXIT
SETUP C.4 DELTA DAYS: 1
0 0 2 ENTR EXIT
SETUP C.4 DELTA D AYS:2
<SET
SET> EDIT EXIT
SETUP C.4 DELTA TIME00:00
<SET SET>
EDIT EXIT
SETUP C.4 DELTA TIME: 00:00
0 0 :3 0 ENTR EXIT
SETUP C.4 DELTA TIEM:00:30
<SET
SET> EDIT EXIT
SETUP C.4 STARTING TIM E:14:15
<SET
SET> EDIT EXIT
EXIT returns
to the SETUP
Menu
SETUP C.4 DURATION:15.0 M INUTES
<SET SET>
EDIT EXIT
SETUP C.4 DURATION 15.0MINUTES
3 0 .0 ENTR EXIT
SETUP C.4 DURATION:30.0 M INUTES
<SET
SET> EDIT EXIT
Toggle keys
to set
duration for
each
iteration of
the
sequence:
Set in
Decimal
minutes
from
0.1 – 60.0
SETUP C.4 CALIBRATE: OFF
<SET SET>
EDIT EXIT
SETUP C.4 C ALIBR ATE: OFF
ON ENTR EXIT
SETUP C.4 CALIBRATE: ON
<SET SET> EDIT
EXIT
Toggle key
between
Off and
ON
SETUP C.4 SEQ 2) ZERO–SPAN, 2:00:30
PREV NEXT
MODE SET EXIT
Sequence Delta Time
MODE Delta Days
7.9. Calibration Quality Analysis
After completing one of the calibration procedures described above, it is important to
evaluate the analyzer’s calibration
SLOPE and OFFSET parameters. These values describe
the linear response curve of the analyzer, separately for NO and NO
X
. The values for these
terms, both individually and relative to each other, indicate the quality of the calibration. To
124 044100102 Rev A