Teledyne 200A Скачать руководство пользователя страница 69

Страница: 69 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

Table 5-12: RS-232 Command Summary

Commands

Definition

? [id]

Print help screen.

is an optional instrument ID number

T [id] LIST

Print all active test messages

T [id] LIST name or
T [id] name

Print single test message "name" from Table 5-15

W [id] LIST

Print all active warnings

W [id] CLEAR name or
W [id] name

Clear single warning message "name" from Table 5-16

C [id] command

Execute calibration "command" from Table 5-17

D [id] LIST

Prints all I/O signal values

D [id] name

Print single I/O signal value/state

D [id] name=value

Sets I/O signal to new "value"

D [id] LIST NAMES

Lists diagnostic test names

D [id] ENTER name

Enters and starts 'name' diagnostic test

D [id] EXIT

Exits diagnostic mode

D [id] RESET

Resets analyzer(same as power-on)

D [id] RESET RAM

System reset, plus erases RAM. Initializes DAS, NO, NO

, NO

conc

readings, calib not affected.

D [id] RESET EEPROM

System reset, plus erases EEPROM (RESET RAM a setup
variables, calibration to default values). Restores all factory defaults.

D [id] PRINT

Prints properties for all data channels (DAS)

D [id] PRINT "name”

Prints properties for single data channel. Quotes around name are
required.

D [id] REPORT "name"
[RECORDS=number]
[COMPACT|VERBOSE]

Prints DAS records for a data channel. Quotes around name are
required. Parameters in brackets are optional.

V [id] LIST

Print all setup variable names and values

V [id] name

Print individual setup variable value

V [id] name=value

Sets setup variable to new "value"

V [id] CONFIG

Print analyzer configuration

V [id] MODE

Print current analyzer mode

5-29

Содержание 200A





























































































































































































































Результаты поиска

Содержание 200A

Отзывы:

Teledyne 200A, Инструкция по эксплуатации, Страница: 69 / 220

Результаты поиска

Содержание 200A

Отзывы: