manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 28 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 28

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

3.2  EPA Equivalency Designation 

Advanced Pollution Instrumentation, Inc., Model 200A Nitrogen Oxides Analyzer is designated 
as Reference Method Number RFNA-1194-099 as defined in 40 CFR Part 53, when operated 
under the following conditions:  

1.

 

Range: Any range from 50 parts per billion (ppb) to 1 ppm. 

2.

 

Ambient temperature range of 5 to 40

o

C. 

3.

 

Line voltage range of 105-125 VAC, 60Hz; 220-240 VAC, 50Hz. 

4.

 

With 5-micron TFE filter element installed in the internal filter assembly. 

5.

 

Sample flow of 500 ± 50 cc/min. 

6.

 

Vacuum pump (internal or external) capable of 10"Hg Abs pressure @ 2 slpm or better. 

7.

 

Software settings: 

A.

 

Dynamic span 

OFF 

B.

 

Dynamic zero 

OFF 

C.

 

Cal-on-NO2 OFF 

D.

 

Dilution factor 

OFF 

E.

 

AutoCal 

ON or OFF 

F.

 

Independent range 

ON or OFF 

G.

 

Autorange 

ON or OFF 

H.

 

Temp/Pres compensation  ON  

I.

 

Converter Eff. 

Acceptable values of 0.96 to 1.02 

 

Under the designation, the Analyzer may be operated with or without the following options: 

1.

 

Rack mount with slides. 

2.

 

Rack mount without slides, ears only. 

3.

 

Rack mount for external pump w/o tray. 

4.

 

Stainless steel zero/span valves. 

5.

 

Internal zero/span. 

6.

 

NO

2

 permeation tube - uncertified 0.4ppm @ 0.7 lpm. 

7.

 

NO

2

 permeation tube - certified 0.4ppm @ 0.7 lpm. 

8.

 

NO

2

 permeation tube - certified 0.8ppm @ 0.7 lpm. 

9.

 

NO

2

 permeation tube - uncertified 0.8ppm @ 0.7 lpm. 

10.

 

4-20mA, isolated outputs. 

11.

 

Status outputs. 

12.

 

RS-232 output. 

13.

 

Internal pump or external pump. 

14.

 

1 micron sample filter. 

3-2 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов