Teledyne 200A Скачать руководство пользователя страница 199 | Manualshive

Страница: 199 / 220

Teledyne 200A Скачать руководство пользователя страница 199

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

9.3.7

The flow/pressure sensor board consists of 2 pressure sensors and a flow sensor. See Figure 9-8
for a diagram of this board. From these three sensors four values are computed and displayed on
the front panel TEST funcions. They are:

1.

Ozone flow - measured directly - S3, R3

2.

Reaction Cell Pressure - measured directly - S2, R2

3.

Sample gas pressure - measured directly S1, R1

4.

Sample Flow - computed from sample pressure and reaction cell pressure S1, S2

The above pressures and flows are filtered to produce the front panel readings. There is a small
delay after adjustment for a steady reading when observing the TEST functions.

To adjust the OZONE flow:

1.

Go to DIAG mode by pressing SETUP-MORE-DIAG, then select SIGNAL I/O, and

press ENTR. Select OZONE_FLOW by using NEXT-PREV keys.

2.

Adjust R3 so that OZONE_FLOW reads 2000 mV. This is the coarse adjustment.

3.

Press EXIT to return to the SAMPLE mode. Select the OZONE FL - TEST function. Use

a calibrated flow meter to make small adjustments in R3 to dial in correct flow.

To adjust the SAMPLE PRESSURE:

1.

Go to DIAG mode by pressing SETUP-MORE-DIAG, then select SIGNAL I/O, and

press ENTR. Select SAMPLE_PRESS by using NEXT-PREV keys.

2.

Adjust R1 to read 4100 mV, which will give approximately the correct pressure.

3.

Press EXIT to return to the SAMPLE mode. Select SAMP - TEST function. Use a

calibrated absolute pressure meter to make small adjustments to R1 until the correct absolute
pressure is displayed. 29.92 in-Hg-A is the target value at sea level. The rate of decrease is
about 1"-Hg per 1000 ft of altitude.

To adjust the REACTION CELL PRESSURE:

1.

Go to DIAG mode by pressing SETUP-MORE-DIAG, then select SIGNAL I/O, and

press ENTR. Select RCELL_PRESS by using the NEXT-PREV keys.

2.

Adjust R2 to read 1450 mV, which will give approximately the correct pressure.

3.

Press EXIT to return to the SAMPLE mode. Select RCEL - TEST function. Use a

calibrated absolute pressure meter to make small adjustments to R2 until the correct absolute
pressure is displayed. The target value is about 5 in-Hg-A for the external Thomas pump in
good condition at sea level.

To adjust the SAMPLE FLOW:

Flow/Pressure Sensor

9-57

«
...
197
198
199
200
201
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов