manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 132 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 132

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

 

NOTE 

If the instrument is to be turned off for more than 8 hours, the  

perm tube must be removed from the IZS oven. Even at room  

temperature the perm tube continues to release NO

2

. Concentrations  

can build up to very high levels inside the instrument causing  

contamination and high background readings. 

 

8.5  Replacing the IZS Zero Air Scrubber 

The IZS zero air scrubber is located on the rear panel of the instrument. Refer to Table 8-1 for 
recommended replacement interval. The entire cartridge can be replaced, or just the charcoal and 
Purafil inside the cartridge. To replace the scrubber materials: 

1.

 

Disconnect the scrubber from the rear panel pneumatic fitting and remove from the hold 

down clip. While removing the cartridge, check the DFU filter for contamination and dirt, 
replace if necessary. 

2.

 

Unscrew the top, remove the felt pad and empty the contents.  

3.

 

Inspect the upper and lower felt pads for signs of plugging, replace if necessary. 

4.

 

Replace with 50% Purafil(upstream) and 50% charcoal (downstream). 

5.

 

Re-install felt pad, screen and re-tighten cap. Make sure the o-ring in the cap is in good 

shape and squarely seated. 

6.

 

Leak check the assembly, then re-attach scrubber to fitting and clip on rear panel. 

8-6 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов