Teledyne 200A Скачать руководство пользователя страница 13

Страница: 13 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

2 GETTING STARTED

2.1 Unpacking

Verify that there is no apparent shipping damage. If damage has occurred please advise

shipper first, then Teledyne API.

CAUTION

To avoid personal injury, always use two persons to

lift and carry the Model 200A

Before operation, it is necessary to remove the shipping hold-down screws. Remove the

instrument cover, then refer to Figure 2-1 for screw location.

Also check for internal shipping damage, and generally inspect the interior of the

instrument to make sure all circuit boards and other components are in good shape and all
boards are seated properly.

Please check the voltage and frequency label on the rear panel of the instrument for

compatability with the local power before plugging in the M200A.

2.2 Electrical and Pneumatic Connections

Refer to Figure 2-2 to locate the rear panel electrical and pneumatic connections.

Attach the pump to the Exhaust Out port on the rear panel as shown in Figure 2-3.

If you are connecting to a calibrator, attach a vented sample inlet line to the sample inlet

port. The pressure of the sample gas at the inlet port should be at ambient pressure. The
exhaust from the pump should be vented to atmospheric pressure. See Figure 2-3 for inlet
and exhaust line venting recommendations during calibration.

If desired, attach the analog output connections to a strip chart recorder and/or

datalogger. Refer to Figure 9-4 for the jumper settings for the desired analog output voltage
range. Factory default setting is 0-5 VDC.

Connect the power cord to the correct voltage line, then turn to Section 2.3 Initial

Operation.

2-1

Содержание 200A





























































































































































































































Результаты поиска

Содержание 200A

Отзывы:

Teledyne 200A, Инструкция по эксплуатации, Страница: 13 / 220

Результаты поиска

Содержание 200A

Отзывы: