manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 124 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 124

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 7-19:  Calibration Quality Check 

Step Number 

Action 

Comment 

1. 

Scroll the TEST 
function menu until 
the NO

x

 SLOPE is 

displayed 

The SLOPE value for NO

x

 should be 1.0 ± 0.3. If the value is 

not in this range, check Section 9.1.6. If the SLOPE value is in 
the acceptable range the instrument will perform optimally. 

2. 

Scroll the TEST 
function menu until 
the NO SLOPE is 
displayed 

The SLOPE value for NO should be 1.0 ± 0.3. If the SLOPE is 
in the acceptable range the instrument will perform optimally. If 
the value is not in this range, check Section 9.1.6.  
 
NOTE:  
The NO and NO

x

 slopes should be equal within ± 0.1. 

3. 

Scroll the TEST 
function menu until 
the NO

x

 OFFSET is 

displayed 

This number should be near zero. A value of 0.0 – 20 + 150 
indicates calibration in the optimal range. This number already 
has the AutoZero value subtracted out and is mainly the 
background signal due to the molybdenum converter. If the 
OFFSET value is outside this range, check Section 9.1.6. 

4. 

Scroll the TEST 
function menu until 
the NO OFFSET is 
displayed 

The instrument will now display the NO OFFSET value. It 
should also have a value near zero (0.0 –20 + 150 mV). This 
number already has the AutoZero reading subtracted out and 
should be near zero. If the OFFSET value is outside this range, 
check Section 9.1.6. 

 

After the above procedure is complete, the M200A is ready to measure sample gas. 

7-36 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов