manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 119 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 119

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

7.8.10.2

  

Precision Check 

A periodic check is used to assess the data for precision. A one-point precision check must be 
carried out at least once every 2 weeks on each analyzer at an NO

2

 concentration between 0.08 

and 0.10 ppm. The analyzer must be operated in its normal sampling mode, and the precision test 
gas must pass through all filters, scrubbers, conditioners, and other components used during 
normal ambient sampling. The standards from which precision check test concentrations are 
obtained must be traceable to NIST-SRM. Those standards used for calibration or auditing may 
be used. 

7.8.10.3  Precision Check Procedure 

1.

 

Connect the analyzer to a precision gas that has an NO

2

 concentration between 0.08 and 

0.10 ppm. An NO

2

 precision gas may be generated by either GPT or a NO

2

 permeation tube. 

If a precision check is made in conjunction with a zero/span check, it must be made prior to 
any zero or span adjustments. 

2.

 

Allow the analyzer to sample the precision gas until a stable trace is obtained. 

3.

 

Record this value. NO and NO

x

 precision checks should also be made if those data are 

being reported. Information from the check procedure is used to assess the precision of the 
monitoring data; see Section 2.0.8 (Q.A. Handbook) for procedures for calculating and 
reporting precision. 

7.8.11  Recommended Standards for Establishing Traceability 

To assure data of desired quality, two considerations are essential: (1) the measurement process must 
be in statistical control at the time of the measurement and (2) the systematic errors, when combined 
with the random variation in the measurement process, must result in a suitably small uncertainty. 

Evidence of good quality data includes documentation of the quality control checks and the 
independent audits of the measurement process by recording data on specific forms or on a quality 
control chart and by using materials, instruments, and measurement procedures that can be traced to 
appropriate standards of reference. To establish traceability, data must be obtained routinely by 
repeated measurements of standard reference samples (primary, secondary, and/or working 
standards). More specifically, working calibration standards must be traceable to standards of higher 
accuracy, such as those listed below in Table 7-18. 

7-31 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов