TELEDYNE API T300 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 347

TELEDYNE API T300 Скачать руководство пользователя страница 48

Getting Started

Teledyne API – Model T300/T300M CO Analyzer

46

instrument will remain latched until it is cleared. You can clear the warning on the front
panel by either pushing the CLR button on the front panel or through the serial port.

In instruments that sample more than one gas type, there could be more than one gas
type triggering the Concentration 1 Alarm (“Alarm 2” Relay). For example, the T300M
instrument can monitor both CO & CO

2

gas. The software is flexible enough to allow

you to configure the alarms so that you can have 2 alarm levels for each gas.

CO Alarm 1 = 20 PPM

CO Alarm 2 = 100 PPM

CO

2

Alarm 1 = 20 PPM

CO

2

Alarm 2 = 100 PPM

In this example, CO Alarm 1 & CO

2

Alarm 1 will both be associated with the “Alarm 2”

relay on the rear panel. This allows you do have multiple alarm levels for individual
gasses.

A more likely configuration for this would be to put one gas on the “Alarm 1” relay &
the other gas on the “Alarm 2” relay.

CO Alarm 1 = 20 PPM

CO Alarm 2 = Disabled

CO

2

Alarm 1 = Disabled

CO

2

Alarm 2 = 100 PPM

“A

LARM

4”

R

ELAY

This relay is connected to the “range bit”. If the instrument is configured for “Auto
Range” and the instrument goes up into the high range, it will turn this relay on.

3.3.1.8.

CONNECTING THE COMMUNICATION INTERFACES

The T-Series analyzers are equipped with connectors for remote communications
interfaces:

Ethernet

,

USB

,

RS-232

, optional

RS-232 Multidrop

, and optional

RS-485

.

In addition to using the appropriate cables, each type of communication method must be
configured using the SETUP>COMM menu, Section 6. Although Ethernet is DHCP-
enabled by default, it can also be configured manually (Section 6.5.1) to set up a static
IP address, which is the recommended setting when operating the instrument via
Ethernet.

E

THERNET

C

ONNECTION

For network or Internet communication with the analyzer, connect an Ethernet cable
from the analyzer’s rear panel Ethernet interface connector to an Ethernet access port.
Please see Section 6.5 for description and setup instructions.

For manual configuration, see Section 6.5.1.

For automatic configuration (default), see Section 6.5.2.

06864D DCN7562

«
...
46
47
48
49
50
...
»

Содержание T300




























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды