manualshive.com logo in svg

TELEDYNE API T300, Руководство по эксплуатации

Поделиться
Скачать
TELEDYNE API T300 Скачать руководство пользователя страница 241

Teledyne API – Model T300/T300M CO Analyzer 

Troubleshooting and Service 

239

 

Table 11-1:  Warning Messages - Indicated Failures 

WARNING 

MESSAGE 

FAULT CONDITION 

POSSIBLE CAUSES 

BENCH TEMP 

WARNING 

The optical bench temp is 

controlled at 48 

±

 2

 °

C. 

Bad bench heater  
Bad bench temperature sensor 
Bad relay controlling the bench heater 
Entire relay board is malfunctioning 
I

2

C bus malfunction 

BOX TEMP 

WARNING 

Box Temp is  

< 5 

°

C or > 48 

°

C. 

NOTE: Box temperature typically runs ~7

o

C warmer than ambient 

temperature.   
Poor/blocked ventilation to the analyzer. 
Stopped exhaust-fan 
Ambient temperature outside of specified range  

CANNOT DYN 

SPAN 

Dynamic Span operation failed 

Measured concentration value is too high or low. 
Concentration slope value to high or too low 

CANNOT DYN 

ZERO 

Dynamic Zero operation failed 

Measured concentration value is too high. 
Concentration offset value to high. 

CONFIG 

INITIALIZED 

Configuration and Calibration data 

reset to original Factory state. 

Failed disk on module 
User erased data 

DATA INITIALIZED 

Data Storage in DAS was erased 

Failed disk on module 
User cleared data 

PHOTO TEMP 

WARNING 

PHT DRIVE is   

>4800 mVDC 

Failed IR photo-detector 
Failed sync/demod board  
IR photo-detector improperly attached to the sample chamber  
Bench temp too high. 

REAR BOARD NOT 

DET 

Motherboard not detected on power 

up. 

 

Warning only appears on serial I/O com port(s) 
Front panel display will be frozen, blank or will not respond. 
Massive failure of motherboard 

RELAY BOARD 

WARN 

The CPU cannot communicate with 

the Relay Board. 

I

2

C bus failure 

Failed relay board 
Loose connectors/wiring 

SAMPLE FLOW 

WARN 

Sample flow rate is < 500 cm

3

/min 

or > 1000 cm

3

/min. 

Failed sample pump 
Blocked sample inlet/gas line 
Dirty particulate filter 
Leak downstream of critical flow orifice 
Failed flow sensor/circuitry 

SAMPLE PRES 

WARN 

Sample Pressure is <10 in-Hg or 

 > 35 in-Hg 

Normally 29.92 in-Hg at sea level 

decreasing at 1 in-Hg per 1000 ft of 

altitude (with no flow – pump 

disconnected). 

If sample pressure is < 10 in-hg: 
Blocked particulate filter 
Blocked sample inlet/gas line 
Failed pressure sensor/circuitry 
If sample pressure is > 35 in-hg: 
Pressurized sample gas.  Install vent 
Blocked vent line on pressurized sample/zero/span gas supply 
Bad pressure sensor/circuitry 

06864D DCN7562

Содержание T300




























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды