background image

Appendix B Radio Information

B.1 RF WWAN Specifications

The Regesta Smart PLC model with the EC25 module provides connectivity for networking over several radio fre-
quency bands under 3GPP Standards.

• LTE (3GPP Release 10),

• DC-HSPA+ (3GPP Release 8),

• HSPA+ (3GPP Release 7),

• HSUPA (3GPP Release 6),

• HSDPA (3GPP Release 5),

• and GSM, GPRS, EDGE (3GPP Release 99 with Feature Package#1).

This product is supplied without any antennas. Choosing antennas is at the discretion of the operator, but said party
is responsible for fulfilling the local regulations.

Technology: LTE.

Bands

Frequencies

Conducted Transmit Power

Band 1

Tx: 1920-1980 MHz

Rx: 2110-2170 MHz

+23 dBm ± 2 dB

Band 3

Tx: 1710–1785 MHz

Rx: 1805–1880 MHz

+23 dBm ± 2 dB

Band 7

Tx: 2500–2570 MHz

Rx: 2620–2690 MHz

+23 dBm ± 2 dB

Band 20

Tx: 832–862 MHz

Rx: 791–821 MHz

+23 dBm ± 1 dB

Technology: UMTS(WCDMA)/ HSDPA/ HSUPA/ HSPA+/ DC-HSPA+.

Bands

Frequencies

Conducted Transmit Power

Band 1

Tx: 1920-1980 MHz

Rx: 2110-2170 MHz

+24 dBm +1/-3 dB

Band 8

Tx: 880–915 MHz

Rx: 925–960 MHz

+24 dBm +1/-3 dB

Technology: GSM / GPRS / EDGE.

Bands

Frequencies

Conducted Transmit Power

EGSM 900 (900 MHz)

Tx: 880–915 MHz

Rx: 925–960 MHz

+33 dBm ± 2 dB

+27 dBm ± 3 dB

DCS 1800 (1800 MHz)

Tx: 1710–1785 MHz

Rx: 1805–1880 MHz

+30 dBm ± 2 dB

+26 dBm ± 3 dB

Teldat S.A.

Radio Information

Regesta Smart PLC

37

Содержание Regesta Smart PLC











































Отзывы: