manualshive.com logo in svg

Teldat REGESTA 1, Руководство по установке и настройке, Страница: 42 / 47

Поделиться
Скачать
Teldat REGESTA 1 Скачать руководство пользователя страница 42

A.3 SNMP TRAPS

The device supports the following SNMP TRAPS:

Name:

gprINICIO_REGISTRO

Description:

This is sent every time the modem starts up or is newly registered, when the
GPRS module resets.

Enterprise

1.3.6.1.4.1.2007

Generic

6

Specific

101

Arguments

• IMSI Octetstring(0..32)

• IP NetworkAddressName Octetstring(0..32)

• LAC Octetstring(0..32)

• Octetstring Cell (0..32)

• Octetstring Group (0..32)

Severity

Message

Device $1requesting register.

Name

gprCOBERTURA_BAJA

Description

The device reports that the coverage is below a threshold.

Enterprise

1.3.6.1.4.1.2007

Generic

6

Specific

121

Arguments

Maximum Integer Threshold

Severity

Message

The device’s coverage is below the maximum threshold

Message

If the parameters don’t follow a pattern: DEVICE $1 REGISTERED

Name

gprCOBERTURA_NORMAL

Description

The device reports that the coverage has been restored to above a threshold.

Enterprise

1.3.6.1.4.1.2007

Generic

6

Specific

122

Arguments

Minimum Integer Threshold

Severity

Technical Information

Teldat S.A.

38

REGESTA 1

Содержание REGESTA 1
















































Отзывы:

Нет отзывов