manualshive.com logo in svg

Tektronix TLA7000 Series, Руководство по установке

Поделиться
Скачать
Tektronix TLA7000 Series Скачать руководство пользователя страница 92

Restoring and Reinstalling Software

Table 5: TLA user

fi

le suf

fi

xes, (cont.)

Suf

fi

x

Description

.stk

Stack

fi

les

.spz

Protocol

fi

les

Once you

fi

nd the

fi

les, copy them to the external storage device. Use this

procedure to

fi

nd any

fi

les or applications that you may want to save.

If you purchased any microprocessor support packages, you need to reinstall the
application after you reinstall the hard disk image. If you do not have a copy of
the microprocessor support software, contract your Tektronix Account Manager
to order a replacement copy. If you cannot contact the account manager, contact
the Tektronix Support Center (refer to

Contacting Tektronix

at the beginning

of this document).

NOTE.

You can reinstall the Microsoft Windows operating system and other

software only from the Hard Disk Image CDs that came with your instrument.
These software applications are licensed and cannot be reinstalled by any other
method without violating the license agreements.

Installing the Operating

System and TLA

Application Software

This procedure reformats the hard disk, installs the operating system software,
and installs the Tektronix Logic Analyzer application software. Because this
procedure reformats the hard disk drive, be sure to back up any

fi

les or software

that you want to preserve by following the steps in the previous section.

CAUTION.

To avoid losing user

fi

les on your hard disk, back them up before

proceeding.

Change the BIOS Boot Settings.

Before installing the Hard Disk Image, you may

need to change the BIOS settings to enable booting the logic analyzer from the
CD-ROM.

74

TLA7000 Series Logic Analyzers Installation Manual

Содержание TLA7000 Series


























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды