Tektronix TLA7000 Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 121

background image

Basic Installation

Figure 27: Instrument search results

Installing the TLA Application Software on a PC

The TLA application CD includes the application software that allows you to
control the logic analyzer from a remote PC. Install the TLA application software
on a PC for the following purposes:

To run the TLA application software in the Of

fl

ine mode.

Control a logic analyzer with the same TLA Application Software over a
network.

Perform the following procedure to install the TLA application software on your
PC for remote operation.

1.

Insert the TLA Application Software CD in the CD drive.

2.

Browse to the TLA Application SW folder on the CD and run the Setup.exe
program. Follow the on-screen instructions.

If you have an older version of the software on the hard disk, the installation
program will detect it and ask if you want to remove it. Follow the on-screen
instructions to remove the software, answering "Yes" to any prompts. Do not
cancel the uninstall program, as this may cause undesirable effects. Restart
the PC when prompted.

Load Third-Party Software.

After installing the TLA application software on your

PC, you can install the additional third-party software, such as SnagIt, (included
on the TLA Application Software CD V5.1, or higher).

The NI-GPIB software allows you to use the iView software with your PC.

The SnagIt software is useful for copying screen shots of logic analyzer data
for use with other applications.

TLA7000 Series Logic Analyzers Installation Manual

29

«
...
45
46
47
48
49
...
»

Содержание TLA7000 Series


























































































































Отзывы:

Нет отзывов

Похожие инструкции для TLA7000 Series

Бренд: Bacharach Страницы: 87

Goldmann AT 870

Бренд: Haag-Streit Страницы: 20

Бренд: IFR Страницы: 46

Бренд: jenway Страницы: 18

Бренд: Flytec Страницы: 2

Бренд: JENCO Страницы: 13

Бренд: THORLABS Страницы: 21

Vigilantplant NFBU200-S Series

Бренд: YOKOGAWA Страницы: 24

Бренд: horiba Страницы: 117

Бренд: Sequid Страницы: 111

Бренд: Badger Meter Страницы: 24

Бренд: Parker Страницы: 16

Бренд: Waterproof Страницы: 51

Бренд: Vectronics Страницы: 28

AquiTron AT-WFM

Бренд: aquilar Страницы: 20

RLACS277RLACS29

Бренд: Racelogic Страницы: 10

Бренд: A&D Страницы: 2

Бренд: Rinstrum Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды