Tektronix TLA7000 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 121

background image

Basic Installation

Figure 6: Portable mainframe setup (up to two modules)

Network Con

fi

guration

Overview

The benchtop mainframe requires an external PC controller; you can use the
TLA7PC1 Benchtop PC Controller or your PC loaded with the TLA application
software. The controller and mainframes communicate through Ethernet
connections.

This section covers con

fi

guring your network settings and establishing

communication between the controller and benchtop mainframes. After making
the cable connections, all of the network con

fi

guration options generally follow

these steps:

1.

Start the controller and mainframe and exit any TLA applications.

2.

Establish LAN connectivity using the Windows Networking tools (set the
IP addresses, and if necessary, get user names and passwords from your IT
group).

3.

Start the TLA application on the controller.

4.

Find and connect to the TLA mainframe through software control.

5.

Repeat for all mainframes in the test system.

6.

Operate the TLA from the controller or remote computer.

Stand-alone Installation

(Benchtop Mainframe)

After making connections with either a crossover cable (peer-to-peer) or a LAN
cable, get the IP addresses to use for the controller and mainframes.

The following

fi

gure shows the stand-alone setup for the benchtop mainframe.

Figure 7: Benchtop mainframe setup (up to six modules)

TLA7000 Series Logic Analyzers Installation Manual

11

«
...
27
28
29
30
31
...
»

Содержание TLA7000 Series


























































































































Отзывы:

Нет отзывов

Похожие инструкции для TLA7000 Series

SXNP10 - DIGITAL PIANO

Бренд: Panasonic Страницы: 63

Бренд: Lumel Страницы: 32

Dusty Harp Pickup Series

Бренд: Dusty Strings Страницы: 5

Бренд: Energometrika Страницы: 39

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Bruker BioSpin Страницы: 76

Бренд: QuantAsylum Страницы: 35

C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1

Бренд: Sierra Страницы: 55

Бренд: ScienTECH Страницы: 44

Бренд: GE Страницы: 16

Бренд: Skil Страницы: 80

Бренд: Erma Electronic Страницы: 24

Бренд: Percussion Play Страницы: 3

Бренд: Fiso Страницы: 31

Бренд: General Страницы: 2

Бренд: GCI Страницы: 44

Бренд: Alma Automotive Страницы: 171

SAFEMASTER S UH 5947

Бренд: DOLD Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды