Tektronix TDS5032 Скачать руководство пользователя страница 51

Страница: 51 / 248

Operating Basics

Configuring Receiver Sensitivity Measurements

To configure receiver sensitivity measurements, follow these steps:

Select the High Speed measurement tab> More button> Receiver Sensitivity
measurement.

To access the Configure Measurements menu, select Measurements>
Configure.

Figure 15: Configuring Receiver Sensitivity measurement

Select the Source from Ch1 to Ch4.

Select the Run button.

Select OK and follow the on-screen prompts to perform the tests.

To generate reports, select Utilities> Report Generator.

Configuring Chirp Measurement

To configure chirp measurements, follow these steps:

Select the High Speed measurement tab> More button> Chirp measurement.

To access the Configure Measurements menu, go to Measurements>
Configure.

In the Configure tab, you can select the DUT (Host or Device) and perform
selected tests associated with it.

TDSUSB2 Universal Serial Bus Measurement Package

Содержание TDS5032

























































































































































































































































Результаты поиска

Содержание TDS5032

Отзывы:

Бренды по названию

Популярные бренды

Tektronix TDS5032, Руководство пользователя

Результаты поиска

Содержание TDS5032

Отзывы:

Бренды по названию

Популярные бренды