manualshive.com logo in svg

Tektronix TDS5032, Руководство пользователя

Поделиться
Скачать
Tektronix TDS5032 Скачать руководство пользователя страница 178

Reference 

 

Note:

 Use the Alt key with only the first keystroke. Release the Alt key before you 

press the final key. For example, to use the shortcut key AltF+D, press the Alt 
and F keys together. Release the keys and then press D.  

USB2.0 Specifications 

This section gives the USB2.0 values for measurements for Low, Full and High 
speed signals.  

Low Speed 

Table 31. Low Speed measurements 

 

USB Limits 

User Configure Limits 

References* 

Measure-

ments    

Max Min  Max. 

range 

 

Min. range 

 

 

Cross-Over 
Voltage  

2.0 V 

1.3 V 

1.6-2.4 V  

1.04-1.56 V  Chapter 7, Table 7-7, 

Section 7.1.2.1 

Signal Rate  

1.5225 Mbps  1.4775 Mbps  1.5675-1.881 

Mbps 

1.146-
1.4325 

Mbps 

Chapter 7, 7.1.11  

Consecutive 

Jitter  

<25 ns  

N/A 

20-30 ns 

N/A 

Chapter 7, 7.1.13.1 

Paired Jitter 

<10 ns 

N/A 

8-12 ns 

N/A 

Chapter 7, 7.1.13.1 

Rising Edge 

Rate 

35.2 V/

μ

s 8.8 

V/

μ

s 

N/A N/A 

From 

MATLAB 

scripts 

Falling Edge 

Rate 

35.2 V/

μ

s 8.8 

V/

μ

s 

N/A 

N/A 

Chapter 7, 7.1.2.1 

EOP Width 

1.5e-6 s 

1.25e-6 s 

1.2-1.8 

1-1.5 ns 

Chapter 7, 7.1.13.2.1

 

*

The References Section refers to the chapter numbers in the ‘Universal Serial 

Bus Specifications Revision 2.0-2000’. 

Note 1: 

Results within the USB limit lead to a PASS condition. Results within the 

waiver limits, but outside USB limits lead to a Conditional PASS. Results within 
the user configured limits lead to PASS. When user configure limits is selected, 
you can view only the result details.

 

Note 2:

Testing at Tier 6 leads to a PASS. Testing at Tier 5 and 4 leads to a 

Conditional PASS that is a Pass within the waiver limits. Testing at Tier 1 to 3 
leads to a FAIL. 

 

 

164 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDS5032

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды