Tektronix RSA3303B Скачать руководство пользователя страница 15

Страница: 15 / 79

Installation

Installation

This section describes how to install this instrument. The topics are organized as
follows:

Unpacking to check contents

Setting up the stand

Applying the power

Functional check

Powering off the analyzer

Restart

Backing up the user

Before starting installation, you should become familiar with the

General Safety

Summary

. (See page iv.)

Unpacking to Check Contents

This product is packed in a cardboard box for delivery. Before opening the
box, make sure that there is no damage on the surface.

Open the box, check that the product has no damage. If you

nd any damaged

or missing components, contact your local Tektronix representative.

It is recommended to keep the box and packing materials. You may need them
to send this product to Tektronix for calibration or repair.

CAUTION.

The analyzer has exhaust fans on the side panel. Leave a space of at

least 5 cm (2 in) on both sides for proper air circulation.

Setting Up the Stand

To set up the stand, place the analyzer on a table. Lift the front of the analyzer and
pull out the stand until it is perpendicular to the analyzer.

RSA3303B, RSA3308B, and RSA3408B User Manual

Содержание RSA3303B
















































































Результаты поиска

Содержание RSA3303B

Отзывы:

Бренды по названию

Популярные бренды

Tektronix RSA3303B, Руководство пользователя

Результаты поиска

Содержание RSA3303B

Отзывы:

Бренды по названию

Популярные бренды