background image

P77DESKEW Fixture Instructions

The P77DESKEW probe deskew

fi

xture provides an edge source to time-align

(deskew) signals at the inputs of P7700 Series probes. The

fi

xture provides a

means to deskew two probes at the same time. The probe and the

fi

xture are

powered by one of the USB ports of the oscilloscope; a USB cable (Tektronix part
number, 174-6919-xx) is included with the

fi

xture.

For performing the deskew procedure, Tektronix recommends using a
DPO/MSO70000C/70000DX series oscilloscope.

Connectors on the

fi

xture accept solder tips that are available for the P7700 Series

probes. The

fi

xture can also be used to deskew probes with browser accessories.

CAUTION.

The probes used with the deskew

fi

xture are ESD sensitive. To avoid

damaging the probes, perform these procedures at an antistatic workstation, with
an anti-static wrist strap while observing proper ESD practices. Refer to your
probe user manual for the anti-static information.

For best performance, you should check the calibration status of the oscilloscope
before performing the deskew procedure. If the oscilloscope requires calibration
or the probe requires compensation, perform these steps before deskewing the
probes. Refer to your oscilloscope manual for instructions on performing the
oscilloscope calibration procedures.

Check the calibration

status

To check the calibration status of the probe, perform the following steps:

1.

Select Probe Cal... from the Vertical menu.

2.

Select the channel to which the probe is attached and then check the Probe
Status readout. There are three possible values for the status:

Initialized

. The probe has not been calibrated on the selected channel;

perform the DC probe calibration procedure.

Compensated

. The probe has been calibrated on the selected channel.

Fail

. The probe has not been calibrated; repeat the procedure.

If the test continues to fail, troubleshoot the problem; do not continue with the
deskew procedure.

www.tek.com
Copyright © Tektronix

*P077126300*

077-1263-00

Содержание P77DESKEW









Отзывы: