Tektronix DPO2304SX Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 920

Tektronix DPO2304SX Скачать руководство пользователя страница 222

To use

■

Click Undo. Only the parameters set by the last autoset are undone. The settings you have changed since the last autoset
(that are not controlled by Autoset) remain unchanged.

■

Click OK to close the window and proceed without an Undo.

Behavior

The Autoset Undo window remains open until you click Undo or OK. After the Autoset Undo window closes, you can still undo the
last autoset by selecting Undo Last Autoset from the Edit or Horiz/Acq menus; the last autoset is immediately undone but the
Autoset Undo control window does not open again.

To suppress the AutoSet Undo window following an autoset, do the following:

1. From the Utilities menu, select User Preferences.

2. Open the Prompts tab.

3. Under Prompt user before performing requested action, toggle the Autoset Undo button to Off.

What do you want to do next?

Learn about Autoset.

Enable enhanced effective number of bits

From the Horiz /Acq menu, select Horizontal/Acquisition Setup, and then select the Acquisition tab.

Overview

Use this control to turn the Enhanced Effective Number of Bits (ENOB) on or off to optimize waveform detail.

To use

1. Click the Enhanced Effective Number of Bits check box to turn ENOB On or Off. You will find this control in the

Acquisitions tab of the

Horizontal/Acquisition control window

Behavior

Enhanced Effective Number of Bits enables interleave correction DSP that improves the effective number of bits. This control is
only available in some instrument models. This control is not available in Hi Res mode.

When Enhanced Effective Number of Bits is enabled, EB

+

is displayed in the horizontal/acquisition readout.

Horizontal and acquisition setups

190

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

«
...
220
221
222
223
224
...
»

Содержание DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов