manualshive.com logo in svg

Tektronix BERTScope BSA Series, Инструкция по эксплуатации

Поделиться
Скачать
Tektronix BERTScope BSA Series Скачать руководство пользователя страница 25

Product disassembly procedures

Reassemble the instrument

CAUTION.

The circuit boards and cables can be damaged if you incorrectly install the cover/enclosure. Make sure that you

do not damage any circuit boards or cables when you slide the chassis into the instrument enclosure.

Make sure that you have correctly installed the hard disk drive bracket before continuing the following steps:

1.

Carefully slide the chassis into the cover shell making sure that none of the cables get pinched outside the shell. Verify
that the EMI gasketing is seated on the front edges of the shell.

CAUTION.

To avoid damaging the power cord connector, center the power connector in the hole as you tighten the screws.

2.

Attach the chassis to the cover shell using the six screws that you removed earlier. Do not tighten the screws until
all of them have started.

a.

Install one of the center screws while moving the chassis as needed to align the screw holes; install the second
center screw.

b.

Attach the four outside screws moving the chassis as needed to align the screws.

3.

Tighten all of the screws to 10.0 in.-lbs using a T15 tip.

Tektronix BERTScope BSA Series Declassi

fi

cation and Security Instructions

15

Содержание BERTScope BSA Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды