Tektronix AFG31000 Series Скачать руководство пользователя страница 34

Страница: 34 / 66

Performance verification

AFG31000 Series Arbitrary Function Generator Specification and Performance Verification Technical Reference

Calibration self-tests

This self-test uses an internal calibration routine that checks and adjusts the internal calibration

constants.

Equipment required

None

Prerequisites



Power on the instrument and allow it to warm up for 20 minutes before

running the self-tests.



Make sure the instrument is operating in an ambient temperature between 0

°C and 50 °C.

To run the calibration self-test:

1. On the display, select

Utility > Diagnostics/Calibration

2. Next to Self-Calibration, select

Run

3. Make sure all cables are disconnected from the instrument and select

4. Wait until the test is complete (the test will take several minutes).
5. Review the results of the test on the display and select

Close

when you are done.

If the diagnostics self-

test completes without ﬁnding any problems, the message

PASSED

is displayed.

When an error is detected during diagnostics execution, the instrument displays an error code. Error

codes are described in

Error codes

(on page 35).

NOTE.

Do not turn off the power while running self-calibration. If the power is turned off during

calibration, data stored in internal nonvolatile memory may be lost.

Содержание AFG31000 Series



































































Результаты поиска

Содержание AFG31000 Series

Отзывы:

Бренды по названию

Популярные бренды

Tektronix AFG31000 Series, Спецификация и техническое описание проверки производительности

Результаты поиска

Содержание AFG31000 Series

Отзывы:

Бренды по названию

Популярные бренды