Tektronix 318, Техническое руководство

Страница: 488 / 555

TM 11-6625-3145-14
318/338 Service
REPLACEABLE
MECHANICAL PARTS
PARTS ORDERING INFORMATION
Replacement parts are available from or through
your local Tektronix Inc. Field Office or representative
Changes to Tektronix Instruments are sometimes
made to accommodate improved components as they
become available and to give you the benefit of the latest
circuit improvements developed in our engineering
department It is therefore important when ordering parts,
to include the following information in your order Part
number instrument type or number serial number, and
modification number if applicable
If a part you have ordered has been replaced with a
new or improved part, your local Tektronix, Inc. Field
Office or representative will contact you concerning any
change in part number
Change information if any is located at the rear of
this manual
ITEM NAME
In the Parts List an Item Name is separated from the
description by a colon (:) Because of space limitations,
an Item Name may sometimes appear as incomplete For
further Item Name Identification the U S Federal
Cataloging Handbook H6-1 can be utilized where
possible
FIGURE AND INDEX NUMBERS
Items in this section are referenced by figure and
index numbers to the illustrations
INDENTATION SYSTEM
This mechanical parts list is indented to indicate item
relationships Following is an example of the indentation
system used in the description column
1 2 3 4 5 Name & Description
Assembly and or Component
Attaching parts for Assembly and or Component
- - - * - - -
Detail Part of Assembly and or Component
Attaching parts for Detail Part
- - - * - - -
Parts of Detail Part
Attaching parts for Parts of Detail Part
- - - * - - -
Attaching Parts always appear in the same
indentation as the item it mounts. while the detail parts
are indented to the right indented Items are part of, and
included with, the next higher indentation The separation
symbol - - -* - - -indicates the end of attaching parts
Attaching parts must be purchased separately,
unless otherwise specified.
ABBREVIATIONS
“ INCH ELCTRN ELECTRON IN NCH SE SINGLE END
# NUMBER SIZE ELEC ELECTRPICA: INCAND NCANDESCENT SECT SECTION
ACTR ACTUATOR ELCTLT ELECTROLYTIC INSUL INSULATOR SEMICOND
SEMICONDUCTOR
ADPTR ADAPTER ELEM ELEMENT INTL INTERNAL SHLD SHIELD
ALIGN ALIGNMENT EPL ELECTRICAL PARTS LIST L.PHLDR LAMPHOLDER SHLDR
SHOULDERED
AL ALUMINUM, EQPT EOUIPMENT MACH MACHINE SKT SOCKET
ASSEM ASSEMBLED EXT EXTERNAL MECH MECHANICAL SL SLIDE
ASSY ASSEMBLY FIL FILLISTER HEAD MTG MOUNTING SLFLKG SELF-LOCKING
ATTEN ATTENUATOR FLEX FLEXIBLE NIP NIPPLE SLVG SLEEVING
AWG AMERICAN WIRE GAGE FLH FLAT HEAD NON WIRE NOT WIRE WOUND SPR SPRING
HO BOARD FLTR FILTER ORD ORDER BY DESCRIPTION SO SQUARE
BRKT BRACKET FR FRAME or, FRONT OD OUTSIDE DIAMETER SST STAINLESS
STEEL
BRS
BRASS FSTNR FASTENER OVH 0VAL HEAD STL STEEL
HRZ BRONZE FT FOOT PH BRZ PHOSPHOR BRONZE SW SWITCH
RSHG BUSHING FXD FIXED PL PL.AIN or PLATE T TUBE
'AB CABINET GSKT GASKET PLSTC PL ASTIC TERM TERMINAL
CAP CAPACITOR HDL HANDLE PN PART NUMBER THD THREAD
CER CERAMIC HEX HEXAGON PNH PAN HEAD THK THICK
SHAS CHASSIS HEX HD HEXAGONAL HEAD PWR POWER TNSN TENSION
CKT CIRCUIT HEX SOC HEXAGONAL SOCKET RCPT RECEPTACLE TPG TAPPING
COMP COMPOSITION HLCPS HELICAL COMPRESSION RES RESISTOR TRH TRUSS
HEAD
CONN
CONNECTOR HLEXT HELICAL EXTENSION ROGD RIGID V VOLTAGE
COV COVER HV HIGH VOLTAGE RLF RELIEF VAR VARIABLE
CPLG COUPLING IC INTEGRATED CIRCUIT RTNR RETAINER W WITH
CRT CATHODE RAY TUBE ID INSIDE DIAMETER SCH SOCKET HEAD WSHR WASHER
DEG DEGREE IDENT IDENTIFICATION SCOPE OSCILLOSCOPE XFMR TRANSFORMER
DVVR DRAWER IMPLR MPELLER SCR SCREW XSTR TRANSISTOR
10-1