Tektronix 310A Скачать руководство пользователя страница 69

Страница: 69 / 132

Performance Check/Calibration-Type 310A

22. Check Upper Vertical Bandwidth Lim it

a. Equipment required for steps 22 through 37 is shown

in Fig. 5-15.

b. Connect the high-frequency constant-amplitude sine-

wave generator to the vertical INPUT connector through

the GR to BNC adapter, 42-inch 50-ohm BNC cable and the

50-ohm BNC termination, in given order.

c. Set the constant-amplitude generator for a four-

division display centered on the graticule at its reference

frequency (50 kilohertz).

d. Without changing the output amplitude, increase the

output frequency of the generator until the display is

reduced to 2.8 divisions (—3 dB point).

e. CHECK—Output frequency of generator must be

f o u r

megahertz or higher.

f. Set the VO LTS/DIV switch to .05.

g. Set the constant-amplitude generator for a four-

division display, centered on the graticule, at its reference

frequency (50 kilohertz).

h. Without changing the output amplitude, increase the

output frequency of the generator until the display is

reduced to 2.8 divisions (—3 dB point).

i. CHECK—Output frequency of generator must be 3.5

megahertz or higher.

j. Repeat parts g through i with the VO LTS/D IV switch

set to .02 and .01.

k. Disconnect all test equipment.

e. C H ECK-CRT display 2.8 divisions or greater in

amplitude (not more than - 3 dB).

f. Disconnect all test equipment.

24. Check High-Frequency Triggering Operation

a. Change the following control settings:

VO LTS/D IV

Input Coupling

T IM E /D IV

f i S E C

b. Connect the high-frequency constant-amplitude sine-

wave generator to the vertical INPUT connector through

the GR-to-BNC adapter, 42-inch 50-ohm BNC cable, 50-

ohm BNC termination and the BNC T connector. Connect

the output of the BNC T connector to the EXT TRIG

INPUT binding post with the 18-inch BNC-to-banana plug

patch cord.

c. Set the high-frequency generator for a two-division

display at two megahertz.

d. CHECK—Stable CRT display is presented.

e. Set the high-frequency generator for a two-division

display at four megahertz.

f. Set the T IM E /D IV switch to .5 juSEC.

g. CHECK—Stable CRT display can be obtained with

the Trigger Coupling-Mode switch set to AC and DC (TRIG

LEVEL control may be adjusted as necessary to obtain a

stable display).

h. Change the following control settings:

TRIGGER

+ EXT

Trigger Coupling-Mode

AUTO

T IM E /D IV

10*zSEC

23. Check AC-Coupled Lower Vertical Bandwidth

Limit

a. Change the following control settings.

VO LTS/DIV

T IM E /D IV

1.2 SEC

b. Connect the low-frequency constant-amplitude sine-

wave generator to the vertical INPUT connector through

the BNC-to-dual binding post adapter, 42-inch 50-ohm BNC

cable and the 50-ohm BNC termination.

c. Set the low-frequency generator for a four-division

display, centered on the graticule, at a reference frequency

of one kilohertz.

d. Without changing the output amplitude, reduce the

output frequency of the generator to two hertz.

i. Set the high-frequency generator for a two-division

display (two volts) at its reference frequency (50 kilohertz).

j. Set the T IM E /D IV switch to ,5^SEC.

k. Without changing the output amplitude, set the

constant-amplitude generator to two megahertz.

. CHECK—Stable CRT display is present.

m. Without changing the output amplitude, set the

constant-amplitude generator to four megahertz.

n. CHECK—Stable CRT display can be obtained with

the Trigger Coupling-Mode switch set to AC and DC (TRIG

LEVEL control may be adjusted as necessary to obtain a

stable display).

o. Disconnect the high-frequency generator.

5-19

Содержание 310A





































































































































Результаты поиска

Содержание 310A

Отзывы:

Tektronix 310A, Инструкция по эксплуатации, Страница: 69 / 132

Результаты поиска

Содержание 310A

Отзывы: