background image

 

VOT1; Rev 1.5; EN; 5.11.2015  

TKT66 

– Installation and maintenance 

 

11

 

4.5  Control unit 

The monitoring function of the central battery unit can operate using three different operating principles: 
addressable monitoring, circuit monitoring or a combination of both. This is selected with the DIP switch 
4 (see more information in Chapter 

5.2.3 DIP switch settings in circuit boards)

. Addressable monitoring 

and circuit monitoring can be set for different circuit boards within the same unit: 8 circuits on 
addressable monitoring, 8 circuits on circuit monitoring, etc. 

In addressable monitoring of the luminaires, each luminaire has its own unique address.

 

There can be 

1...32 luminaires in one circuit. The luminaires have LOW 1-16 (luminaires 1-16) and HIGH 1-16 
(luminaires 17-32) addresses. For example, the luminaire HIGH 2 indicates luminaire number 18. On 
the display of the central battery unit this is presented with the letters 

(LOW) or 

(HIGH). The central 

battery unit checks the operation and indicates the result for each luminaire separately. 

The circuit monitoring measures the current of a circuit in battery mode. The changes in the current are 
used to determine possible faults in the circuit. The number of luminaires in a circuit is not limited, but 
the input power of a circuit cannot exceed 350 VA or 1,6 A. Note t

hat circuit monitoring doesn’t give 

luminaire-specific information. The limit value of the error alarm can be changed in the settings, (1-31) = 
+/- 10.. 310 mA. The factory settings are 16 = +/- 160 mA. 

NOTE: 

In parallel connection, the current values are multiplied by the number of the parallel connected 

circuits. 700 W = 2x or 1400 W = 4x. 

NOTE: 

If circuit monitoring current limits are changed in a configured centre, the unit goes into a non-

configured state and must be re-configured.

 

The descriptions of the signal LEDs and the buttons are presented in chapters 

4.9 Control Module 

panel luminaire 

monitoring LED’s and menu settings

 and 

4.11 Buttons. 

4.5.1 Individual luminaire monitoring test with basic settings 

As a basic setting, the luminaire test is done automatically once a day at a predetermined time. The 
central battery unit carries out the test as follows: 

The central battery unit switches to battery mode and the 

Battery Oper

. and the 

Luminaire Test

 LEDs are 

lit for the duration of the test. L or H and the circuit number is displayed on the display of the control unit. 
Whenever  a  functioning  luminaire  is  detected,  an  indicator  light  is  lit.  After  all  circuits  are  tested,  the 
system returns to normal mode. 

If a malfunctioning luminaire is found from any circuit, an indicator light will blink on the display. Also, the 

External fault 

LED is lit and the external error alarm relay will operate. In correctly functioning luminaires 

the LEDs are lit evenly. 

For more information about testing the luminaires, see Chapter 

4.10 Control Module panel test functions 

and alarms.

 

4.5.2 Circuit monitoring luminaire test with basic settings 

As a basic setting, the luminaire test is done automatically once a day at a predetermined time. The 
central battery unit carries out the test as follows: 

The central battery unit switches to battery mode and the 

Luminaire test 

LED

 

is lit for the duration of the 

test. The current of each circuit is measured and the circuit number increases as the test progresses. 
The LEDs representing the measured relative current of each circuit will be lit. After all circuits have 
been tested, the software returns to normal mode.  

A fault indication will be given if in any of the circuits the measured current differs more than +/- 80 mA 
when compared to the value which was stored during the last configuring. Each one LED in the column 
represents a +/- 100 mA of current in a circuit. The deviation against the configured value is shown by 
flashing the LEDs corresponding the difference. The more LEDs there are flashing, the bigger is the 
difference and more luminaires are likely to be failed. With the settings the current range can be 
changed between 10 and 310 mA. The displays of the LEDs also operate in within this range. Also, in 

Содержание TKT66

































































Отзывы: