Tecumseh OHH50 - 65 Скачать руководство пользователя страница 78

Страница: 78 / 94

OIL SEAL

OIL SEAL REMOVER

TOOL: POSITIONED FOR

REMOVAL OF OIL SEAL

OIL SEAL

DRIVER 670272

OIL SEAL

DRIVER

PROTECTOR

OIL SEAL

CYLINDER COVER, OIL SEAL, AND BEARING SERVICE

The following procedures, except oil seal replacement, require the engine to be disassembled. See "Engine

Disassembly Procedure" in this chapter.

Cylinder Cover

Clean and inspect the cover, looking for wear and scoring of the bearing surfaces. Measure the bearing surface

diameters using a micrometer and check the specifications for worn or damaged parts. Replace as necessary.
When reinstalling the cover, apply a drop of Loctite 242 to the cover screw threads and torque the cover screws

to the recommended specification. Always use new gaskets and new oil seals installed using seal protectors

after the cover is removed.

Oil Seal Service

NOTE:

BEFORE REMOVING THE OIL SEAL,

CHECK TO SEE IF THE SEAL IS RAISED OR

RECESSED. WHEN INSTALLING A NEW OIL SEAL,

TAP IT INTO POSITION GENTLY UNTIL IT IS

SEATED INTO ITS BOSS. SOME SEALS ARE NOT

POSITIONED FLUSH TO THE CYLINDER COVER.

ATTEMPTING TO INSTALL THE SEAL TOO FAR IN

CAN CAUSE DAMAGE TO THE OIL SEAL AND

ENGINE.
If the crankshaft is removed from the engine, remove

the old oil seals by tapping them out with a screwdriver

or punch from the inside. If the crankshaft is in place,

remove the seal by using the proper oil seal puller

(diag. 50).
Select the proper seal protector and driver from the

tool list in Chapter 11 to install a new oil seal. Place

the oil seal over the protector and place it over the

crankshaft. Drive the seal into position using the

universal driver part no. 670272. The seal protector

will insure that the seal is driven in to the proper depth

(diag. 51).

CRANKSHAFT BEARING SERVICE
Ball Bearing Service

Remove the two bearing retainer screws and washers.

Remove the ball bearing in the cylinder cover by

pressing the bearing from the outside of the cover

toward the inside using an arbor press.
Install a new ball bearing by pressing the bearing from

the inside of the cover toward the outside until the

bearing contacts the shoulder. Install the two bearing

retainer screws with washers and tighten to 45 in. lbs.

(5.0 Nm) of torque.

SNAP RING

OIL SEAL REMOVED

Содержание OHH50 - 65































































































Результаты поиска

Содержание OHH50 - 65

Отзывы:

Tecumseh OHH50 - 65, Руководство пользователя, Страница: 78 / 94

Результаты поиска

Содержание OHH50 - 65

Отзывы: