manualshive.com logo in svg

Tecumseh OHH50 - 65, Руководство пользователя, Страница: 34 / 94

Поделиться
Скачать
Tecumseh OHH50 - 65 Скачать руководство пользователя страница 34

31

PULLEY AND REWIND
SPRING ASSY.

BRAKE SPRING

STARTER DOG

DOG
SPRING

WASHER

SPRING PIN

STARTER HOUSING

HANDLE
INSERT

ROPE

HANDLE

WASHER

RETAINER

6

ROPE

STARTER
HOUSING

HANDLE

PULLEY AND REWIND
SPRING ASSY.

STARTER DOG

BRAKE SPRING

7

Assembly Procedure

1. Reverse the disassembly procedure. The

starter dogs with the dog springs must snap

back to the center of the pulley (disengaged

position). When the rope is pulled, the tabs

on the retainer must be positioned so that they

will force the starter dogs to engage the starter

cup. (diag. 6 & 7)

2. Install a new recoil spring if necessary by

pushing the new spring out of the holder into

the pulley cavity while aligning the outside

spring hook into the deep notch in the pulley.

Push the spring cover in until seated.

3. Always replace the center spring pin with a

new one upon reassembly. Place the two new

plastic washers between the center leg of the

starter and the retainer. New plastic washers

are provided with a new center spring pin.

Discard the old plastic washer.

4. Place the rewind on a flat surface and drive

the new center pin in until it is within 1/8"

(3.175 mm) of the top of the starter.

NOTE:

 DO NOT DRIVE THE CENTER PIN

IN TOO FAR.
The retainer will bend and the starter dogs

will not engage the starter cup. On the

stamped steel starter the center pin should

be driven in until it contacts the shoulder in

the starter housing.

5. Replacing rope wind the starter pulley

counterclockwise four or five turns to pre-load

the recoil spring and thread the rope through

the starter housing eyelet. Pull enough rope

through to tie a temporary knot in the rope.

Reattach the starter handle to the rope using

a left-hand knot. Untie the temporary knot and

allow the rope to recoil.

STYLIZED REWIND STARTER WITH

PLASTIC RETAINER
Disassembly Procedure

1. After removing the rewind assembly from the

engine blower housing, remove the starter

handle by first pulling a length of rope out

using the handle, tying a temporary knot in

the exposed rope, and either untying the knot

in handle or prying out the staple.

2. Untie the temporary knot and slowly allow the

rope to fully retract into the starter housing

and the recoil spring to fully unwind.

3. Remove the decal from the center of the

starter housing.

DOG RETAINER

RETAINER WEDGE

STARTER
HOUSING

DOG SPRING

STARTER DOG

STARTER PULLEY
SPRING & COVER

8

LEFT-HAND
KNOT

DOG  SPRING

WASHER

RETAINER

WASHER

SPRING PIN

Содержание OHH50 - 65































































































Отзывы:

Нет отзывов