TECNICOMAR BICOMPACT Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 42

TECNICOMAR BICOMPACT Скачать руководство пользователя страница 29

Instructions for the installation, use and maintenance of Tecnicomar watermaker

7-29

7.5

General maintenance plan

7.5.1

Prefiltering circuit

Components

Required maintenance

Maintenance Period

Prefilters

Clean or replace filter cartridges
and clean the sump

(1)

When the low pressure (Lbar) falls
below 0.5 bar

7.5.2

Pressurizing circuit

High pressure pump

Change oil (only for CAT
pump)

(1)

First change: after 3 months or 50 hours
of operation; then every year or after
every 500 hours of operation.

Membrane

Replace the membrane

(2)

module

When the UNSAFE warning message
does not go off and the produced water
is not fresh.

Membrane

Cleaning procedure

(2)

When the fresh water production is less
than 30% of the production with new
membranes.

7.5.3

Controls and produced water circuits

Salinity sensor and temperature

Clean the conductivity electrodes 24 months

Salinity meter

Calibrate using a conductivity
meter with a scale in
microSiemens/cm

After replacing or cleaning the salinity
sensor

7.6

Maintenance kit

The maintenance kit allow to have on board a sufficient stock of filter cartridges and other parts that may be required
for the ordinary system maintenance.

A complete Maintenance Kit contains:



No.8 prefilter cartridges 30 micron



No.8 prefilter cartridges 5 micron



No.2 active carbon cartridges



No.1 FL/403 membrane storage solution



No.1 FL/411/A Type A membrane cleaning solution



No.1 FL/412/B Type B membrane cleaning solution



No.1 1500 mm high-pressure hose



No.2 containers of pump oil (in case of high pressure CAT pump)



No.2 O-rings for prefilters

To order a complete Maintenance Kit, please specify the series and the model of your watermaker (ex. series SAILOR
C mod. 1500).

(1)

Use only TECNICOMAR original oil and filter cartridges

(2)

C

ontact a TECNICOMAR Authorized Center

FL/411A  CONTAINS  SODIUM  HYDROXIDE  and  FL/412B  CONTAINS  CITRIC  ACID  :
DO  NOT  BREATHE  DUST,  AVOID  CONTACT  WITH  SKIN  &  EYES.  CAUSES
IRRITATION  TO  EYES  AND  MUCOUS MEMBRANES.  HARMFUL  IF  SWALLOWED.
IN  CASE  OF  CONTACT  FLUSH  EYES  OR  SKIN  WITH  WATER  AND  CONTACT  A
DOCTOR.

«
...
27
28
29
30
31
...
»

Содержание BICOMPACT











































Отзывы:

Нет отзывов