manualshive.com logo in svg

technoswitch ORYX200 Series, Руководство по установке и эксплуатации

Поделиться
Скачать
technoswitch ORYX200 Series Скачать руководство пользователя страница 12

ORYX202 ORYX204 ORYX208 Conventional Fire Panels 

– INSTALLATION & OPERATION MANUAL 

 

 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx 

E&OE 

- 12 - 

 

Figure 6

 

ORYX208 Weatherproof Enclosure 

1.8 

WIRING INSTALLATION 

All electrical wiring installation work should be carried out in accordance with the code of practice or applicable 
national standards appropriate to the country of installation. 

To maintain electrical integrity all zone, input, output, and communication line wiring should be segregated from 
the AC Mains wiring and be wired using cable with insulation suitable for the application. 

To minimise the effects of EMC interference, all data wiring circuits should be wired with a twisted pair of 
conductors with a cross sectional area suitable for the loading conditions. 

In areas where cabling may come into contact with high frequency interference, such as portable radio 
transceivers etc., the data wiring cable should be of a twisted pair construction within an overall screen. Care 
should be taken to correctly terminate this screen, refer to the relevant sections of this manual for further 
information for each circuit type. 

NB:

 

Minimum/Maximum cable size for all external connections is limited to 0.5 mm²/2.5 mm² (22 

– 14 AWG). 

1.8.1 

RECOMMENDED CABLE ROUTING 

It is recommended that the typical routing arrangement shown in Figure 7 and Figure 8 be followed. 

Segregate the low voltage wiring (Zone Circuits, Sounder Circuits and AUX Supply) from the AC Mains Wiring. 

Segregate any wiring connected to the relay contacts. 

Refer to the specific sections on how to install AC Mains Input and Loop, Sounder, Relay and AUX Outputs 
Circuits. 

Содержание ORYX200 Series


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды