Technosoft iPOS360x MX Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 116

Technosoft iPOS360x MX Скачать руководство пользователя страница 82



Technosoft 2013

70

iPOS360x MX Technical Reference

TechnoCAN  uses  only  identifiers  outside  of  the  range  used  by  the  default  by  the  CANopen
predefined  connection  set  (as  defined  by  CiA  301).  Thus,  TechnoCAN  protocol  and  CANopen
protocol  can  co-exist  and  communicate  simultaneously  on  the  same  physical  CAN  bus,  without
disturbing each other.

5.1.5.

Checking Setup Data Consistency

During the configuration phase, a CANopen master can quickly verify using the checksum objects
and a reference

.sw

file (see 0 and 5.2.4 for details) whether the non-volatile EEPROM memory of

an iPOS360x drive

contains the right information. If the checksum reported by the drive doesn’t

match with that computed from the

.sw

file, the CANopen master can download the entire

.sw

file

into the drive EEPROM using the communication objects for writing data into the drive EEPROM.

5.2. Using the built-in Motion Controller and TML

One of the key advantages of the Technosoft drives is their capability to execute complex motions
without requiring an external motion controller. This is possible because Technosoft drives offer in
a single compact package both a state of art digital drive and a powerful motion controller.

5.2.1.

Technosoft Motion Language Overview

Programming motion directly on a Technosoft drive requires creating and downloading a TML
(Technosoft Motion Language) program into the drive memory. The TML allows you to:



Set various motion modes (profiles, PVT, PT, electronic gearing or camming

1

, etc.)



Change the motion modes and/or the motion parameters



Execute homing sequences

2



Control the program flow through:



Conditional jumps and calls of TML functions



TML interrupts generated on pre-defined or programmable conditions (protections

triggered, transitions on limit switch or capture inputs, etc.)



Waits for programmed events to occur



Handle digital I/O and analogue input signals



Execute arithmetic and logic operations



Perform data transfers between axes



Control motion of an axis from another one via motion commands sent between axes



Send commands to a group of axes (multicast). This includes the possibility to start
simultaneously motion sequences on all the axes from the group



Synchronize all the axes from a network

1

Optional for iPOS360x CANopen execution

2

The customization of the homing routines is available only for iPOS360x CAN execution

«
...
80
81
82
83
84
...
»

Содержание iPOS360x MX





















































































































Отзывы:

Нет отзывов