Technogym ISOCONTROL Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 72

Technogym ISOCONTROL Скачать руководство пользователя страница 17

ISOCONTROL: Service & Maintenance Manual - rev. 1.2

Pagina 5.1

5. INSTALLATION INSTRUCTIONS

5.1. SPECIFICATIONS AND REQUIREMENTS

To install the machine correctly, make sure that:

1. The machine is installed on a flat and steady surface able to bear its own weight as well as the

user’s weight.

2. The environment is dust or sand free.
3. The environment meets the operating temperature and humidity conditions specified in

paragraph 2.3.

4. The machine must not be located near any sources of heat, electromagnetic interference (TV

sets, electric motors, antennas, high voltage lines, household appliances etc…) or medical
equipment.

5. The machine must be securely grounded.
6. The power entry must be located in a place where the plugging and unplugging can be done

easily and safely. The power entry is reserved to the machine and supplies at least 60 W power.

7. The machine allows other units to be connected in cascade To ensure a correct link, follow the

recommendations given in paragraph 4.2.2. “Daisy chain”.

8. Place the machine power cable so that people do not trip over it

5.2. INSTALLATION

For correct installation of the machine, proceed as instructed below.

ATTENTION: due to subsequent product modifications, it is possible that the following

procedure may not be up to date. Therefore, in case of any doubt always refer to the
installation manual supplied together with the Isocontrol system, and which can be
ordered with code 0SM00389AA-M1 (Selection) or 0SM00400AA-M1 (Element).

Open the box containing the Isocontrol components and place them on the ground next to the
machine on which the system is being installed.

«
...
15
16
17
18
19
...
»

Содержание ISOCONTROL









































































Отзывы:

Нет отзывов