Tech 21 SansAmp GED-2112 Скачать руководство пользователя

Страница: 6 / 6

SansAmp GED-2112 Specifications

Note:

With on-going product development and improvements, specifications and/or

the cosmetic appearance of this unit may change without prior notice.

Replacement

parts

are available, i.e., knobs, rack handles, faceplate, etc. For more information,

please contact Tech 21.

Model Number:

GED-2112

Input Impedance- Front Input:

1MOhm

Input Impedance-Inputs A & B:

1MOhm

Output Impedance-1/4” SansAmps:

1KOhm min

Output Impedance-XLRs:

600 Ohms min

Input Level-Front Input:

1V RMS max

Input Level-Inputs A & B:

1V RMS or 10V max, with -20dB pad engaged

Output Level-XLRs:

Switchable to -20dB or 0dB range

Effects Loop Send:

1K Ohm min, -20dB

Effects Loop Return:

100K Ohm min, -20dB

Low Frequency Response:

10Hz or better*

High Frequency Response:

Harmonic content, 20kHz or better*

Maximum Power Consumption:

5 Watts

AC Input Power (factory set):

100V, 117V, 230V, 240V

Cycles:

50/60 Hz

NOTE: Each unit constructed for specific voltages. AC power cannot be switched.

Enclosure:

Aluminum and steel, fully shielded

Dimensions:

19.0"w x 1.75"h x 5.25"d / Overall depth: 6.25"

Weight:

5 lbs.

*Due to the variety of amplifier emulations available, frequency response

characteristics will vary.

Содержание SansAmp GED-2112







Результаты поиска

Содержание SansAmp GED-2112

Отзывы:

Похожие инструкции для SansAmp GED-2112

Бренды по названию

Популярные бренды

Tech 21 SansAmp GED-2112, Руководство пользователя

Результаты поиска

Содержание SansAmp GED-2112

Отзывы:

Похожие инструкции для SansAmp GED-2112

Бренды по названию

Популярные бренды