tecan Columbus Washer Скачать руководство пользователя страница 69

Страница: 69 / 82

7. Maintenance and Cleaning

7.5.2 Rinse:

Day

This procedure is used to rinse the wash solution system if the instrument is to be
left standing for a longer time. Alternatively it can be used to rinse the wash
solution system after the instrument has been left for a long time.

With this procedure you can use either distilled water or wash solution.

If the instrument is left to stand for 1 hr to 1/2 day, wash solution can be used, for
longer times use distilled water.

Confirm rinsing solution and tube in bottle

Select and confirm Day Rinse procedure

Select required channel (1 - 4)

Rinse: Day
- + other yes

Day: CH1
- + exit yes

Rinse Solution ?
exit yes

Waste Bottle OK?
exit yes

Confirm waste bottle is empty

Soaking
Stop

The waste sink is filled with solution and
the manifold is lowered into it

Manifold left in solution until

Stop

key pressed

Run XX:yyyyyyy
- + other yes

Standby mode
Washing Procedure can be performed

Rinse ChX YY sec
Stop

Wash system rinsed for set rinse time

May 2003

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

7-11

Содержание Columbus Washer



















































































Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды

tecan Columbus Washer, Инструкция по эксплуатации

Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды