tecan Columbus Washer Скачать руководство пользователя страница 68

Страница: 68 / 82

7. Maintenance and Cleaning

7.5 Rinse

Modes

There are four Rinse modes to flush the liquid system and prevent needle
blockages. They should be carried out when the instrument is left to stand or is
switched off at the end of operation.

The Rinse modes are:

Rinse Soak

Rinse Day

Rinse Night

Rinse Auto

7.5.1 Rinse:

Soak

This procedure is used if the instrument is to be left to stand for a short time.
(1/2 hr. or less).

With this procedure you can use either distilled water or wash solution.

Confirm that the rinsing solution
and the tube are in the bottle

Select and confirm Soak Rinse procedure

Select required channel (1 - 4)

Rinse: Soak

- + other yes

Soak: CH1

- + exit yes

Rinse Solution ?

exit yes

Waste Bottle OK?

exit yes

Confirm waste bottle is empty

Soaking

Stop

The waste sink is filled with solution

and the manifold is lowered into it

Manifold left in solution until

Stop

key pressed

Run XX:yyyyyyy

- + other yes

Standby mode
Washing procedure can be performed

7-10

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

May 2003

Содержание Columbus Washer



















































































Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды

tecan Columbus Washer, Инструкция по эксплуатации

Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды