tecan Columbus Washer Скачать руководство пользователя страница 39

Страница: 39 / 82

4. Operating Instructions

4.5.2

Instrument with Liquid Sensor (Optional)

Waste Bottle Full at Start

When the selected program is confirmed, the instrument checks if the waste
bottle is full. If it is full, the following message is displayed:

Wastebottle Full
yes

Press

yes

to remove the message and return to the start and the following

message is displayed:

Run XX
- + other yes

Empty the waste bottle and restart the program.

Waste Bottle Full during Procedure

If the waste bottle becomes full during the washing procedure, the following
message is displayed after the instrument has completed the washing procedure:

Wastebottle Full
yes

Note:

The instrument does not stop a procedure when the waste bottle becomes full.

Therefore, ensure that the waste full sensor is calibrated, so that there is

enough space in the waste bottle to accept the remaining solution.

(See chapter 6)

Press

yes

to remove the message and the instrument proceeds to the standby

mode and the following message is displayed:

Run XX
- + other yes

Empty the waste bottle and the instrument is ready to start the next procedure.

Liquid Bottle Empty

If the liquid bottle is empty before a program is started, the following message is
displayed:

Liq. Empty Ch: X
yes

Fill the liquid bottle and press

yes

to remove the message and continue with the

program.

May 2003

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

4-11

Содержание Columbus Washer



















































































Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды

tecan Columbus Washer, Инструкция по эксплуатации

Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды