tecan Balance Kit for SAG 285/01 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

tecan Balance Kit for SAG 285/01 Скачать руководство пользователя страница 17

3 - Technical Data

Requirements

Balance Kit Operating Manual, 393278, en, V1.0

3 - 7

Connection via

Uniport

If the computer has only one free RS-232 port and no USB port, the SAG 285/01

may be connected via the Uniport board, provided the following conditions are

fulfilled:

Instrument Software V4.5 or earlier is installed on the computer.

The instrument is equipped with a Uniport board.

Note:

•

Apart from Genesis RMP or instruments used in customized solutions, Tecan

instruments are not normally equipped with a Uniport board.

•

If possible, a separate Uniport board may be installed for the Gravimetric

Test.

•

The connection via the Uniport is not supported by the Instrument Software

version V4.6 or later.

3.3.2 Software

Instrument

Software

Version V4.2 or later is required.

Note:

The connection of the SAG 285/01 via Uniport is no longer supported from

Instrument Software Version 4.6 or later.

Operating

System

According to specifications of installed version of Instrument Software.

Drivers for

USB / RS-232

Converters

The delivery of the recommended USB to RS-232 converters includes drivers that

are suitable for Windows 2000 and Windows XP.

«
...
15
16
17
18
19
...
»

Содержание Balance Kit for SAG 285/01









































Отзывы:

Нет отзывов