background image

Page

Introduction

Thank you for choosing the Losi Mega Baja™ Monster Vehicle. This is a highly developed off-road model that 
features a sophisticated computer-based radio system and  does require some mechanical experience and direct adult 
supervision.  This guide contains the basic instructions and drawings for operating and maintaining your new Mega Baja.
Please take the time to read through it completely before running the model. 

Your hobby dealer cannot under any 

circumstances, accept a model for return or exchange that has been run.

Customer Support Contact:

Horizon Hobby, Inc.

4105 Fieldstone Road

Champaign, IL 61822

1-877-504-0233

[email protected]

Safety Precautions

THIS IS NOT A TOY! The Mega Baja is a sophisticated, high-performance radio controlled model, which needs to be operated 
with caution and common sense. Failure to operate this model in a safe and responsible manner could result in personal
and/or property damage. It is your responsibility to see that the instructions are followed and precautions adhered to. 
The Mega Baja is not intended for use by children without direct adult supervision. Losi, JR and Horizon Hobby shall 
not be liable for any loss or damages, whether direct, indirect, special, incidental or consequential arising from the use, 
misuse or abuse of this product or any product required to operate it.

 * This is still a model; don't expect it to do unrealistic stunts.

Warnings

    Fuel is dangerous if handled carelessly. Follow all directions and precautions on the fuel container.
    Keep fuel and all chemicals out of the reach of children.
    Always keep the fuel container closed and never use around an open flame or while smoking.
    The exhaust emits poisonous carbon monoxide fumes. Always run the model in a well ventilated area and never attempt
to run it indoors.
    The top of the engine and the exhaust pipe are extremely hot during and for a time after use. Use caution not to touch
these parts, especially when refueling.
    The engine can be loud, especially when run in a confined area. If you find the noise objectionable, use ear protection.
    This model is controlled by a radio signal that is subject to interference from sources outside your control. Interference 
can cause temporary loss of control so it is advisable to always keep a safety margin in all directions to avoid collisions.
    Always operate your model in an open area away from people and cars. The potential speed of this model can cause 
injury or damage.

Содержание Losi Mega Baja

























Отзывы: