Teac TN-300, Руководство пользователя

Страница: 4 / 60

4
Precautions for use
o
Do not place anything on the turntable cover. Objects
on the cover might cause noise due to vibrations or
fall off, especially during playback.
o
Avoid placing the unit in direct sunlight, close to a
source of heat or in other similar conditions. Do not
place the unit on top of an amplifier or other equip-
ment that might generate heat that exceeds the
operating temperature range of this unit. Doing so
could cause discoloration, deformation or malfunction.
o
As the unit could become warm during operation,
always leave sufficient space around it for ventilation.
When installing this unit, leave a little space (at least
20 cm (8”)) between it and other devices and walls to
allow good heat dissipation.
When placing it in a rack, for example, leave at least
35 cm (13 3/4”) open above it and 10 cm (4”) open
behind it. Failure to provide these gaps could cause
heat to build up inside and result in fire.
o
DO NOT MOVE THE UNIT DURING PLAYBACK. During
playback, the record rotates. Do not lift or move the
unit during playback. Doing so may damage the
record, the stylus, the cartridge or the unit.
o
Always remove the record before relocating or mov-
ing this unit. Moving the unit with a record on the
turntable could damage the record, the stylus and
the cartridge or could cause a malfunction.
o
The voltage supplied to the unit should match the
voltage as printed on the rear panel. If you are in any
doubt regarding this matter, consult an electrician.
Maintenance
If the surface of the unit gets dirty, wipe it with a soft
cloth or use diluted mild liquid soap. Allow the surface
of the unit to dry completely before using.
o
Do not use chemical cleaning cloths, thinner or simi-
lar substances as they could damage the surface of
the unit.
V CAUTION
For safety, disconnect the power cord from the socket
before cleaning.
Product registration
Customers in the USA, please visit the following TEAC
website to register your TEAC product online.
http://audio.teac.com/support/registration/
Using the TEAC Global Site
You can download updates for this unit from the TEAC
Global Site:
http://teac-global.com/
1) Open the TEAC Global Site.
2) In the TEAC Downloads section, click the desired lan-
guage to open the Downloads website page for that
language.
NOTE
If the desired language does not appear, click Other
Languages.
3) Click the “Search by Model Name” section to open
the Downloads page for that product. (Users in
Europe should click the product name in the
“Products” section instead.)
4) Select and download any updates that are needed.
Before use (continued) Preparing the record player
Keep the unit in standby while setting it up (
E
on
page 6).
1 Place it on a flat surface.
Since the heights of this unit's feet cannot be
adjusted, be sure to place it on a flat surface.
2 Install the turntable.
Align the turntable with the center shaft and install
it.
Center shaft
Turntable
3 Loop the belt around the motor pulley.
Use a finger to pull the rubber belt that is wrapped
around the sub-platter through the round opening
and loop it around the motor pulley.
o
Be careful not to let the rubber become twisted.
o
Rotate the turntable several times to make sure
that it is secure.
Motor pulley
Rubber belt
Round opening
4
Place the rubber mat.
Place the protective rubber mat that is included
with the turntable on it before use.
Top
o
The rubber mat has a top and a bottom. As
shown in the illustration, the side with the ridged
concentric circles should be placed down.
5 Install the counterweight.
Place the counterweight over the end of the tone
arm and turn it clockwise to tighten it.
Counterweight
6
Install the headshell.
Insert the headshell on the end of the tone arm and
turn the nut to secure it in place.
Headshell
Nut