background image

16

16

Licenses

6.1  Reference to the EU Declaration of Conformity

The perforators of the T2212

 

comply with the relevant fundamental regulations 

of the EU Rules for Safety and Health:
•  Directive 2014/30/EU relating to electromagnetic compatibility
•  Directive 2011/65/EU on the restriction of the use of certain hazardous 

substances in electrical and electronic equipment

EU Declaration of Conformity

Please follow the link below, to download the latest T2212 Perforator, EU 

Declaration of Conformity, TE document, T2212-Perforator-CE-EU-C-of- C. 

 

EU Declaration of Conformity

6.2  FCC

NOTE : This equipment has been tested and found to comply with the 

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a commercial 

environment. The equipment generates, uses, and can radiate radio 

frequency and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio commu-

nications. Operation of this equipment in a residential area is likely to 

cause harmful interference in which case the user may be required to 

correct the interference at his own expense.

Содержание T2212

















Отзывы: