TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 7

Страница: 7 / 67

HGP Kit Manual

1.0 Safety

General Safety Instructions

These safety instructions are intended for all work on the HGP filter. Additional safety instructions

are provided at appropriate points on other sections of this manual.

Warning

Be sure to read, understand, and follow all safety

instructions.

Warning

Only qualified electricians should carry out all electrical

installation and maintenance work on the HGP filter.

Warning

All wiring must be in accordance with the National

Electrical Code (NEC) and/or any other codes that apply

to the installation site.

Warning

Disconnect all power before working on the equipment.

Do not attempt any work on a powered HGP filter.

Warning

The HGP filter, drive, motor, and other connected

equipment must be properly grounded.

Warning

After switching off the power, always allow 5 minutes for

the capacitors in the HGP filter and in the drive to

discharge before working on the HGP, the drive, the

motor, or the connecting wiring. It is a good idea to check

with a voltmeter to make sure that all sources of power

have been disconnected and that all capacitors have

discharged before beginning work.

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды