TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 6

Страница: 6 / 67

HGP Kit Manual

1.0 Safety

1.0

Safety

The information presented in this manual covers the HGP filter kits only. For the

full HGP manual please visit:

https://transcoil.com/Products/HGP-Passive-Harmonic-Filter.htm

Safety Instructions Overview

This section provides the safety instructions which must be followed when installing, operating, and

servicing the HGP Filter kit. If neglected, physical injury or death may follow, or damage may occur

to the filter or equipment connected to the filter. The material in this chapter must be read and

understood before attempting any work on or with the product.

The HGP filter is intended to be connected to the input terminals of one or more VFDs. Three-

phase power is connected to the input terminals of the filter and power is supplied to the VFD or

VFDs through the filter. The instructions, and particularly the safety instructions, for the VFDs,

motors, and any other related equipment must be read, understood, and followed when working on

any of the equipment.

Warnings and Cautions

This manual provides two types of safety instructions. Warnings are used to call attention to

instructions that describe steps that must be taken to avoid conditions that can lead to a serious

fault condition, physical injury, or death.

Cautions are used to call attention to instructions that describe steps that must be taken to avoid

conditions that can lead to a malfunction and possible equipment damage.

Warnings

Readers are informed of situations that can result in serious physical injury and/or serious damage

to equipment with warning statements highlighted by the following symbols:

Warning

Dangerous Voltage Warning: warns of situations where

high voltage can cause physical injury and/or damage

equipment. The text next to this symbol describes ways

to avoid the danger.

Warning

General Warning: warns of situations that can cause

physical injury and/or damage equipment by means other

than electrical. The text next to this symbol describes

ways to avoid the danger.

Warning

Electrostatic Discharge Warning: warns of situations in

which an electrostatic discharge can damage equipment.

The text next to this symbol describes ways to avoid the

danger.

Cautions

Readers are informed of situations that can lead to a malfunction and possible equipment damage

with caution statements:

Caution

General Caution: identifies situations that can lead to a

malfunction and possible equipment damage. The text

describes ways to avoid the situation.

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды