TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 58

Страница: 58 / 67

HGP Kit Manual

6.0 Troubleshooting

6.0

Troubleshooting

HarmonicGuard

Passive Filter Status Warning

If the desktop interface indicates a status warning, hover over the status detection for a brief

description. Depending on the condition there are multiple ways to try and clear the status

warnings.

Only qualified electricians should carry out all electrical installation & maintenance work on the

HGP.

Disconnect all sources of power to the and connected equipment before working on the

equipment. Do not attempt any work on a powered HGP.

This HGP unit contains high voltages and capacitors. Wait at least five minutes after

disconnecting power from the filter before attempting to service the conditioner. Check for zero

voltage between all terminals on the capacitors. Also, check for zero voltage between all phases

of the input and output lines. All maintenance and troubleshooting must be done by a qualified

electrician. Failure to follow standard safety procedures may result in death or serious injury.

Unless an external disconnect means has been provided everything ahead of the filter

circuit breaker, including the reactors, will still be energized.

Receiving Inspection

The connectivity board has been thoroughly inspected and functionally tested at the factory and

carefully packaged for shipment. After receiving the unit, immediately inspect the shipping

container and report any damage to the carrier that delivered the unit. Verify that the part number

of the unit received is the same as the part number listed on the purchase order.

Connectivity Board Problem

The HGP is comprised of five major components; the PQconnect connectivity board, the line

reactor, the tuning reactor, the contactor and the capacitors. The PQconnect PCB contains

diagnostic LEDs. The locations of the LEDs are shown in Figure 29 and their functions are listed

in Table 32: LED Functions.

Warning

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды