TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 67

background image

HGP Kit Manual

5.0 PQconnect

38

Modbus RTU

Introduction

The PQconnect Modbus RTU network communication interface transmits and receives command

and status data from the PQconnect Modbus master over a RS-485 serial link. Modbus RTU is a

simple serial communications protocol originally developed by Modicon for use with

Programmable Logic Controllers (PLCs) in control of industrial devices. Modbus RTU is

commonly supported by most PLCs and is an open, royalty-free communications standard.

Wiring and Configuration

The PQconnect implements a Modbus RTU Master/Slave device, which supports two-wire RS-

485 signal levels. The PQconnect communication port used for the Modbus RTU interface is

connected directly to the PCB. The communication port is located on the side of the PQconnect

board.

Figure 24 : PQconnect Modbus RTU Connection

Modbus RTU Display Connections

The hardware pinout for the J5 communication header and default settings is shown below.

5

4

3

2

1

Modbus RTU

Connection

«
...
40
41
42
43
44
...
»

Содержание HGP HarmonicGuard Series




































































Отзывы:

Нет отзывов

Похожие инструкции для HGP HarmonicGuard Series

Бренд: Aqua FX Страницы: 7

EZH2O LZWS-LRPBM28K

Бренд: Elkay Страницы: 4

SENTINEL LEAK DEFENSE LDS-3-075

Бренд: Watts Страницы: 41

Бренд: Oase Страницы: 20

EASYpure II UV 1302 Series

Бренд: Barnstead Страницы: 40

Бренд: Reliable Страницы: 2

Бренд: Envirovent Страницы: 16

Бренд: Filtreco Страницы: 16

Бренд: Antunes Filtration Technologies Страницы: 24

Бренд: Finerfilters Страницы: 18

Бренд: Aquathin Страницы: 52

Бренд: Aquasana Страницы: 16

Бренд: Aquaport Страницы: 9

Бренд: AQUAPHOR Страницы: 12

Бренд: Hydac Страницы: 80

Бренд: XCLEAR Страницы: 15

Бренд: XCLEAR Страницы: 32

Бренд: Propur Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды