TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 25

Страница: 25 / 67

HGP Kit Manual

5.0 PQconnect

Installation

Installation Checklist

The following are the key points to be followed for a successful installation of the PQconnect

board.

Make sure that the installation location will not be exposed to direct sunlight, corrosive

or combustible airborne contaminants, excessive dirt or liquids.

Select a mounting area that will allow adequate cooling air and maintenance access.

Make sure that all wiring conforms to the requirements of the National Electrical Code

(NEC) and/or other applicable electrical codes.

Connect the HGP equipment-grounding lug to the system ground of the premises

wiring system. Use a properly sized grounding conductor.

Connect three-phase power from the KDR Line reactor to the input terminals of the

PQconnect board, J1, J2, and J3.

Connect 120VAC Power (customer supplied) to the input power supply header J12 on

the PCB

Connect RS 485 to USB serial converter to the Modbus RTU header J5.

Use PQvision software from TCI website to calibrate PQconnect PCB.

Ensure all component connections are torqued before energizing filter.

NOTE:

PQvision software is required to calibrate the PQconnect PCB

Mounting

Selecting a Suitable Location

When mounting the PQconnect board, provide an adequately ventilated location to prevent

overheating. Refer to the applicable kit drawings for PCB dimensions. The maximum temperature

of the air around the HGP filter components should not exceed 50°C (122°F). Consult the watts

loss columns above in Filter Wire Sizing for Watts Loss when planning enclosure ventilation.

When selecting a mounting location for the PQconnect PCB, plan for the routing of the power

wiring. Figure 11 Shows a representative schematic of power wiring. Note that there are direct

connections from the KDR line reactor to the PQconnect PCB.

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды