background image

 

 

KMS-2/Exia/Exd Transmitter 

Installation and Operating Manual 

 
 
 
 

 

 

 

 

Page 8 of 16                                        KMS-2:Exia/Exd IOM 

                                     

Rev H    18/05/10

 

 

           

 

 

ATEX 

 

 

 

9.  Press the ‘Span’ button until the ‘Span’ LED stays on 
10.  Wait until the ‘Span’ LED extinguishes. (output 20mA) 

 

 

If the optional LCD is fitted the display will read ‘CAL’ during the setting process. 
The measuring range can be set within the factory limits with a maximum turndown of 50%, 
If  an  error  is  detected  during  the  ranging  process  the  unit  will  default  to  the  previously 
saved values the Relevant LED will flash if ranging failed.  
 

Inverse output 

The output is normally set so that the 20mA point is at the Head shell end. If it is required to mount the 
head shell at the bottom the output can be inverted by following procedure.  

1.  Move the float to approximately 50% of range 
2.  Set the ‘Zero’ level as 2-5 above 
3.  Move the float to the required maximum level 
4.  Set the ‘Span level as 7-9 above, 
5.  Move the float to the required minimum level zero level. 
6.  Set the ‘Zero level as 2-5 above. 

The unit will then automatically invert the output. 

 

Caution 

The  float failure  and  write  protect  switches  should  be  set  to  the  ‘OFF’  position  before 
adjustment to the ranging are made, and reinstated as necessary afterwards.  
It is important that the float is kept stationary for approximately 10 seconds before and 
after operation of the calibration buttons to ensure that the output signal has stabilised 
to the correct value. 
 

 

Low level alarm 

The Low Level alarm output signal will change the output to 3.8mA if the float drops more than 13mm 
below Zero point. When off the output will remain at 4mA below the zero point until the return signal is 
lost i.e. the sensor is no longer sensing the magnetic field then output will change to 22mA. 
 

1) Write Protect 

 

 

Up  

 

Range setting inhibited 

 

 

Down    

 

2) Alarm Function 

Up   

 

Low Level  

(3.8mA) 

Down    

No Alarm Output  

 

 

Remains at 4mA 

 Fig. 6 

Configuration switches 

 

 

 

Caution

 

Turn power off before changing alarm switch settings to prevent unexpected changes in 
loop current. Ensure that the write protect is set to ‘ON’ after changes to range 
adjustments. 
 

 

 

FIXED OUTPUT

 

 
To  allow  for loop  calibration the  transducer  output  can  be  fixed  to  either  4  or  20mA.  The  zero  or  span 
button should be depressed until the respective LED lights; the output will then remain static. To reset to 

 

 

 

Содержание KMS-2

















Отзывы: