TBi Industries PP-TX, Руководство по эксплуатации

Страница: 60 / 63

Operating instructions TBi PP-TX welding torch TBi Industries GmbH
Page 60 / 63 Subject to change without notice.

2020 TBi Industries GmbH
6 Spare and wear parts
Pos. Part no. Description
2 385P021016 Trigger, red, 2 poles
3a 185P102020 Handle Push Pull, right, blue
3b 185P102022 Handle Push Pull, left, blue
3c 100P008411 Screw for TBi handle, 5x12 mm
4 185P102024 Cap Push Pull, blue
11,
12 387P300100 Knob Potentiometer 10 K OHM
387P300022 Knob Potentiometer 2.2 K OHM
387P300047 Knob Potentiometer 4.7 K OHM
14b 580P101082 Spring assembly for pressure roll holder
14c 580P102073 Sleeve
14d 109P091503 Set screw ISO4028-M3x4-45H-A2S
15 580P102037 Knurled nut
19 181P002115 Pressure roll
19a 185P101039 Pressure roll cpl. for AlSi wire
20 195P101022 Compl. pressure roll holder (pre-
assembled)
20a 185P102029 Knurled nut M4, plastic
20b 195P102054 Pressure roll holder
20c 181P002112 Bushing
20d 185P102030 Flat-head screw 3.5 Torx T10 M4x16
20e 195P102057 Hinge pin
100
185P101030 Feed roll for wire 0.8 mm
185P101034 Feed roll for wire 0.9 mm
185P101031 Feed roll for wire 1.0 mm
185P101032 Feed roll for wire 1.2 mm
185P101035 Feed roll for wire 1.4 mm
185P101033 Feed roll for wire 1.6 mm
185P101036 Feed roll for Al wire 1.0 mm
185P101037 Feed roll for Al wire 1.2 mm
185P101038 Feed roll for Al wire 1.6 mm
101 195P102052 Wire guide 0.8 – 1.6 mm
102 195P102068 Inlet guide for wire Ø 0.8-1.0 mm
195P102069 Inlet guide for wire Ø 1.2 mm
Pos. Part no. Description
195P102088 Inlet guide for wire Ø 1.6 mm
195P102059 Inlet guide for wire Ø 0.8-1.0 mm
195P102060 Inlet guide for wire Ø 1.2 mm
120 181P001016
P/C board for connection to main drive
motor
130 185P102027 Plate for Push Pull with 2 potentiometer
131 185P102026 Plate for Push Pull handle w/o poti
140 195P101020 Connection body and motor pre-
assembled
PP-TX, water-cooled
w/o.
fig. 185P101020 Connection body and motor pre-
assembled PP-TX, gas-cooled
142 371P000087 Hose clamp, 8.7 mm
143 373P100095 Hose clamp with ring, 9.5 mm
150 391P000071 Cable retainer 160 x 3.6mm
160 600P102200 Front clamping joint for MIG rubber
hose 25x1.5
170 600P102104 Knuckel spring, large version
180 185P102025 Extension for Push Pull handle, black
- 195P102100 O-ring set for PP-TX torch neck gas-
/water-cooled
Spare parts in bold = standard version