background image

INSTALLATION INSTRUCTIONS

 

DIXON 06-4037HS

ROMAN TUB FAUCET

THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS: 

ASME A112.18.1/CSA B125.1 and NSF-61

TURN OFF

TURN OFF

SI

LI

CO

NE

Your installation may require
new supply lines.
(Supply lines are not included.)

® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.

CUSTOMER SERVICE      WEST 1-800-267-4774   |   EAST 1-800-387-7064   |   taymor.com

THANK YOU

 FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE  CAREFULLY

ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.

HAVE BASIC TOOLS READY

RECOMMENDED TOOLS:

1

Flashlight

Teflon tape Screwdrivers

Adjustable

wrench and

pipe wrench

Plumber’s putty

Safety goggles

Torque wrench

Silicone caulk

2

TURN OFF THE MAIN WATER SUPPLY

Locate water supply inlets and shut off water supply valves. 

These are usually found near water meter.

WARNING: READ ALL

 the instructions completely before beginning.  

READ ALL

 warnings, care and maintenance information.

Taymor recommends calling a professional if you are uncertain about installing this product!

This product should be installed in accordance with all local and provincial plumbing and building codes.

Need Help?

 Please call our toll-free Customer Support line at 

(WEST) 1-800-267-4774     (EAST ) 1-800-387-7064 for additional assistance or service.

3

DECK PREPARATION

Drill holes in FINISHED DECK per diagram.

NOTE: This kit is intended for installation up to 1-1/8” thick.

4

INSTALL THE VALVE SYSTEM

Place a flange (1) on each housing assembly.

Thread each flange down until it locks onto

housing assembly. 

5

HANDLE INSTALLATION

Ensure the o-ring (1) is placed in the handle seat (2) before installing. Then place handle 

assembly (3) onto the right (cold) valve stem (4). Then thread the handle seat (2) onto the 

flange (5). Place the other handle assembly onto the left (hot) valve stem and install the 

same way. After install handle assembly, if the handle seat is not aligned with handle in

a line as shown in the above diagram (6), rotate the handle seat back (the rotating

angle can not exceed 90° ) to make the handle seat align with handle in a line.

7

HOSE GUIDE INSTALLATION

Remove flange (1) from housing assembly.

With the housing assembly marked “HOT” on 

the left, adjust washers (1) and lock nut (2) to 

the bottom of the housing assembly. Insert 

the housing assembly through the mounting 

holes from the underside of the deck/rim.

A

B

C

6

SPOUT INSTALLATION

1

1

1
2

From underneath the deck secure housing 

assembly with lock nut (3) and washers (2). 

Wrench tighten locknut (3). 

D

1

TORQUE

11 - 15 FT/LBS.

TORQUE

11 - 15 FT/LBS.

3

2

Insert hose guide (1) into deck hole.

From underneath deck, secure hose guide

with rubber washer (1), metal washer (2)

and locknut (3). Tighten locknut (3) securely 

with wrench. NOTE: Suggest the torque on 

locknut (3) is in the range of 11-15 ft/lbs.

Connect the flexible water supply hose (1) to the bottom of valve bodies (2) as show. Align middle 

body (3) in a position which will allow maximum clearance to connect hoses. Carefully bend the 

hoses to fit available space. Carefully thread the hose couplings to the sides of the middle body (3). 

NOTE: Suggest the connective torque between (1) and (2), (1) and (3) is in the range of 6-10 ft/lbs.

A

B

C

4~6"

(10.

2-15

.2cm

)

5" m

in.(1

2.7cm)

3" 

min

.

      

      

     

     

      (

7.6c

m)

8~16

"(20.3

-40.6c

m)

Ø1-3/8”

(35mm)

Ø1-1/8”

(29mm)

Ø1-3/8”

(35mm)

Ø1-3/8”

(35mm)

1-1/8

” (29m

m) M

AX. D

ECK

 THIC

KNE

SS

4

3
2

1

6

5

Remove collar (1) from diverter body.

From above, place collar (1) on diverter body. 

Thread collar down until it locks onto diverter body 

fully. From underneath the deck, secure diverter 

body with locknut (3) and washers (2). Wrench 

tighten locknut (3). NOTE: Suggest the torque on 

locknut (3) is in the range of 11-15 ft/lbs.

A

C

1

Adjust washers (1) and locknut (2) to the

bottom of diverter valve, insert the diverter

through the mounting hole from the

underside of the deck/rim.

B

2

1

Assemble and align spout (1) onto diverter

body and tighten set screw with allen wrench 

(2). Place button (3). Thread lift rod (4) onto 

diverter body through the spout (1) tightly.

D

3

2

1

4

1

3

2

1

3

2

1

3

2

2

1

1

Отзывы: