INSTALLATION INSTRUCTIONS
3
FAUCET INSTALLATION
1)
OPTIONAL ESCUTCHEON INSTALLATION: Remove old faucet. Clean sink surface in
preparation for new faucet. Apply a bead of plumber’s putty or silicone caulk around the
faucet openings. Install the gasket over the three holes in your sink.
2)
OPTIONAL ESCUTCHEON INSTALLATION: Screw bolts (1) to the escutcheon (2). Install
escutcheon over the three holes in the sink. From underneath sink, hand tighten mounting
nut. Do not overtighten.
3a) OPTIONAL INSTALLATION ESCUTCHEON: Retract pull-down hose (1) up through faucet
body, until the pull-down hose fitting is flush with the bottom of shank (2). Do not pull hose
fitting past the shank. Insert faucet body through the hole in escutcheon. Note: Do not feed
the pull-down hose (1) back down through the spout until step 3.
3b) OPTIONAL INSTALLATION WITHOUT ESCUTCHEON: Retract pull-down hose (1) up
through faucet body, until the pull-down hose fitting is flush with the bottom of shank (2).
Do not pull hose fitting past the shank. Insert faucet body through the hole. Note: Do not
feed the pull-down hose (1) back down through the spout until step 3.
4) Install rubber washer (1), metal washer (2) onto the threaded mounting shank.Lock nut (3)
into position by tightening screws (4). Do not overtighten.
5) Screw quick connector (2) to the free end of pull-out hose (1).
6) Align block (1) and tabs on quick connect. Push quick connect housing firmly upward and
snap onto receiving block. Pull down moderately to ensure connection has been made. If
it is necessary to remove quick connect, squeeze tabs on hose between index finger and
thumb, then pull down to disconnect. After connecting the hose, install the weights (2) at
the lowest point of the hose.
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
TURN OFF
TURN OFF
SI
LI
CO
NE
Your installation may require new supply
lines. (Supply lines are not included.)
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
WITH OPTIONAL ESCUTCHEON
Do not, use plumber’ putty on cultured marble or other
composite sinks. Putty will discolor the sink.
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
6
EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep
it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel
wool and harsh chemicals as these will dull the finish and void your warranty.
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply
valves. These are usually found under the sink.
WARNING: READ ALL
the instructions completely before beginning.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
06-8724S / 06-8724SSS
SINGLE HANDLE KITCHEN FAUCET
5
FLUSHING THE WATER LINES
Turn on hot and cold water supplies. Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose counterclockwise. Be sure to hold the end
of the hose down into the sink and turn the faucet on to the warm position where it mixes
hot and cold water. Flush water lines for one minute. Check for leaks. Re-tighten any
connections if necessary, but do not overtighten. Reinstall spray head by hand tightening
it back onto the spray hose.
1 - INVERTER
4
ATTACH THE HOT AND COLD SUPPLY LINES
Thread the nut (1) on supply line onto outlet of water supply valve (2) and tighten with
wrench. Do not overtighten.
2 - HOSE
3 - SPRAY HEAD
4 - ESCUTCHEON
5 - BASE PLATE
6 - BOLT
7 - MOUNTING NUT
8 - O-RING
9 - QUICK CONNECT
10 - WEIGHT
11- O-RING
12 - BLOCK
13 - LOCKING SCREW
14 - NUT
15 - METAL WASHER
16 - WASHER
17 - SET SCREW
23 - O-RING
24 - CLIP
25 - WASHER
26 - SPOUT
18 - HANDLE
19 - CONNECT
20 - CAP
21 - BONNET
22 - CARTRIDGE
2
1
1
2
3
2
1
4
1
3b
6
2
4
3a
5
1
2
1
2
2
1
2
1
