Taylor Horizon 8752 страница 43 Скачать руководство пользователя

Страница: 43 / 53

Models 8752, 8756, 8757

Troubleshooting Guide

Section 8

Troubleshooting Guide

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

1. No product is being

dispensed.

a. Low on mix. The MIX

OUT light is on.

a. Add mix to the mix tank

and press the AUTO key.

b. The power switch is in the

OFF position.

b. Place the power switch in

the ON position and press

the AUTO key.

−

c. The beater motor is out on

reset.

c. Reset the freezer.

d. The beater assembly is

rotating counterclockwise.

d. Contact service technician

to correct rotation to

clockwise.

−

e. Insufficient mix in the

freezing cylinder.

e. Refer to problem #2.

−

f. Restriction in the door

spout.

f. Remove the draw handle

and raise the draw valve

all the way up to remove

restriction. Never put

objects or fingers in door

spout.

−

g. Machine is unplugged.

g. Plug machine into the wall

receptacle.

−

h. Circuit breaker is off or the

fuse is blown.

h. Turn the breaker on or

replace the fuse.

−

i. The mix probe was not

installed properly, or was

damaged.

i. Check the mix probe

installation.

2. Insufficient mix in the

freezing cylinder.

a. Suction line is not fully

submerged in the mix.

a. Arrange the suction line

so the weighted end is

fully submerged.

b. Improper seal of suction

line to the mix inlet fitting.

b. Remove the suction line

from the mix inlet fitting.

Place under hot running

water, allow tubing to

swell, then cool. Connect

suction line to barbed

fitting. Eventual

replacement will be

necessary.

−

c. Worn or defective check

bands or o

−

rings in air/mix

pump assembly.

c. Replace regularly. Never

lubricate check bands.

24/ 44

Содержание Horizon 8752






















































Результаты поиска

Содержание Horizon 8752

Отзывы:

Похожие инструкции для Horizon 8752

Бренды по названию

Популярные бренды

Taylor Horizon 8752, Руководство оператора

Результаты поиска

Содержание Horizon 8752

Отзывы:

Похожие инструкции для Horizon 8752

Бренды по названию

Популярные бренды