manualshive.com logo in svg

Taylor C723, Руководство оператора

Поделиться
Скачать
Taylor C723 Скачать руководство пользователя страница 9

Section 2

2-1 

Model C723 

To the Operator 

 2

To the Operator

Your freezer has been carefully engineered and 
manufactured to give you dependable operation.

This machine, when properly operated and cared for, will 
produce a consistent quality product. Like all mechanical 
products, it will require cleaning and maintenance. A 
minimum amount of care and attention is necessary if the 
operating procedures outlined in this manual are followed 
closely.

IMPORTANT! 

This manual should be read 

before operating or performing any maintenance on the 
machine.

Your Taylor machine will 

NOT

 compensate for and/or 

correct any errors made during setup or filling operations. 
Thus, the initial assembly, setup, and priming procedures 
are of extreme importance. It is strongly recommended 
that all personnel responsible for the machine's 
operation, including assembly and disassembly, go 
through these procedures together to be properly trained 
and to make sure that all personnel understand their role 
in using and maintaining the machine.

If you should require technical assistance, please contact 
your local authorized Taylor distributor.

Your Taylor warranty is valid only if the parts are 
authorized Taylor parts, purchased from the local 
authorized Taylor distributor, and only if all required 
service work is provided by an authorized Taylor service 
technician. Taylor reserves the right to deny warranty 
claims on machines or parts if unapproved parts or 
incorrect refrigerant were installed in the machine, 
system modifications were performed beyond factory 
recommendations, or it is determined that the failure was 
caused by abuse, misuse, neglect, or failure to follow all 
operating instructions. For full details of your Taylor 
warranty, please see the Limited Warranty section in this 
manual.

Note:

Constant research results in steady 

improvements; therefore, information in this manual is 
subject to change without notice.

IMPORTANT! 

If the crossed-out waste 

container symbol is affixed to this machine, it signifies 
that this machine is compliant with the EU Directive as 
well as other similar legislation in effect after August 13, 
2005. Therefore, it must be collected separately after its 
use is completed and cannot be disposed as unsorted 
municipal waste. The user is responsible for delivering 
the product to the appropriate collection facility as 
specified by your local code.

For additional information regarding applicable local 
laws, please contact the municipal facility and/or local 
distributor.

Содержание C723

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды